| ||
Visit MustangSteve's web site to view some of my work and find details for: FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events |
1 of 1
Offline
Wondering if you could use Mustang Steve's 2005-2014 front disc brake conversion brackets to mount the Ford Racing M-2300-S GT500 front disc brake kit (which is designed to replace 2005 - 20014 GT and V6 brakes) thereby giving a vintage Mustang late model GT500 front disc brakes? Seems like it should work - might need a fitting adapter for the brake lines, but everything else would seem to bolt up.
Anyone tried this or any thoughts?
Offline
Welcome and thanks for coming over, I posted the invite at VMF!
I can't help you on your question but if you hang in here a bit I'm sure you will get your answer, perhaps even from the "Man" himself.
Offline
You may have to grind a little clearance on my bracket to clear the bigger pistons, but they will work. This has been done by quite a few customers. Also have bracket sets for the 2015-2018 Mustang GT 14” front discs.
18” wheels are required.
Note: the calipers are alot wider and stick out farther. Very limited wheel selection to clear those bad boys.
Offline
MS...appreciate the reply!! Don’t see a set of brackets for 14” discs listed on your website
Last edited by tenthumbs (9/17/2018 7:30 PM)
Offline
Tenthumbs,
I haven’t put the kit up on the website yet, but was planning on trying to get it on there this week. Email me and we can work something out.
Offline
Also, I have a kit for the 2014 GT500 front 14” brakes now too. They also require at least 18” wheels.
Offline
To clarify
The 2005-2014 Mustang GT and GT500 14” brakes use the GT2008-FT
The 2015 and up 14” GT and Brembo beakes will use the GT2015-FT
Offline
Thread revival
What is the caliper bolt spacing on the gt500 calipers or the gt2008-FT brackets?
Offline
Its right around 5 29/32". I'd have to pull the CAD drawing from my laser cutter to get the exact measurement. Let me know if you need that.
Offline
Hey Mike,
Thanks very much for that.
Reason I was asking is I have a set of CTS-V brembo calipers here, that look exactly like the GT500 brembo calipers. The bolt spacing on these calipers are pretty much 5". Looks like the ford ones had a slightly different bolt spacing.
And that 2014 gt500 brake kit you mentioned. Can i confirm that's the 6 piston brembos withn14" rotors to suit?
Thanks again
Offline
The Brembo calipers I used were four piston off a 2014 GT500 14" rotor. Here's a video of a fellow talking about the prototype kit using those 2014 Brembo GT500 14" brakes:
Last edited by mustangermike (10/29/2018 8:22 PM)
Offline
That's for that info Mike. I was gonna ask if you guys used the 4 or 6 piston Brembos.
1 of 1
REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on. |