FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

12/03/2016 9:21 PM  #26


Re: Project Deadhorse....

Josh,  Thanks for the post.  I enjoy hearing about your progress.  It brings back memories.


Fort Walton Beach or Bust (2017 BASH)
 

12/03/2016 10:48 PM  #27


Re: Project Deadhorse....

Thanks Al.....
Today, installed tank to fuel pump fuel line
Tomorrow, rebuilding heater box; seal kit arrived yesterday.....
This 1 h.p. operation is slowly getting there............


.......common sense is a flower that doesn’t grow in everyone’s garden.......
     Thread Starter
 

12/28/2016 11:51 PM  #28


Re: Project Deadhorse....

Finally able today to complete the heater box rebuild......must have done something right last year cause Santa left me a gift card so, that got me a heater core.  One cool thing was when I took the blower motor apart to install new seals, the born on date was ink stamped, Sept 9, 1964 on the blower motor....
Also finished the emergency brake set up.......one more thing crossed off the list
Installing the driver side vent tomorrow.....slow progress but, progress none the less........


.......common sense is a flower that doesn’t grow in everyone’s garden.......
     Thread Starter
 

1/01/2017 11:27 AM  #29


Re: Project Deadhorse....

Good progress Josh. Keep going like that and we'll see it at the BASH!

 

2/19/2017 9:58 AM  #30


Re: Project Deadhorse....

Quick update on project deadhorse.........yesterday had a little time available so, installed drivers side fresh air vent system and buttoned up the emergency brake set up......
Time permitting this week, plan to install the duraspark ignition system and a set of plug wires if I can find a set I really like......
Slow progress but house restoration {ie: nightmare on elm street} is eating my lunch right now......more updates as they come...


.......common sense is a flower that doesn’t grow in everyone’s garden.......
     Thread Starter
 

5/20/2017 5:24 PM  #31


Re: Project Deadhorse....

Josh, I like it keep up the good work.

 

5/20/2017 6:13 PM  #32


Re: Project Deadhorse....

Thanks Barry. Was able to bead blast the hipo headers and slop some POR 15 on then. Got them installed but that's it for now....the house keeps dragging me back.... but I'm on the down wind leg

Last edited by josh-kebob (6/03/2017 10:33 AM)


.......common sense is a flower that doesn’t grow in everyone’s garden.......
     Thread Starter
 

6/03/2017 8:43 AM  #33


Re: Project Deadhorse....

Congratulations Josh.  Making good progress.  Enjoying the pics and narrative.


Fort Walton Beach or Bust (2017 BASH)
 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.