FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Anyone have a junk 4100 laying around? I need a part

    • 1 of 1

       

    1/03/2018 12:11 PM  #1

    Daze
    Forum Moderator & Bash host 2011

    Offline

    From: Kalispell MT
    Registered: 1/24/2013
    Posts: 1,114

    Anyone have a junk 4100 laying around? I need a part

    As many of you know I am modifying a throttle body to fit on an edelbrock 4-barrel intake.  As part of my plan I want it to accept an air cleaner housing just like a carburetor.  To that end I need the top from a scrap 4100 to adapt to the throttle body.  Anyone able to hook me up?

    If it isn't broken...modify it anyway! http://www.DazeCars.com https://galaxieforum.boardhost.com
     

    1/04/2018 8:54 AM  #2

    DC
    Senior 24-7 FYI Addict

    Offline

    From: Marshall, MI
    Registered: 4/01/2013
    Posts: 1,235

    Re: Anyone have a junk 4100 laying around? I need a part

    If you are just making an adapter out of it does it really need to be a 4100? 

     

    1/04/2018 4:02 PM  #3

    Daze
    Forum Moderator & Bash host 2011

    Offline

    From: Kalispell MT
    Registered: 1/24/2013
    Posts: 1,114

    Re: Anyone have a junk 4100 laying around? I need a part

    good point.  I have some other carbs I can use.  The 4100 has the simplest top and I thought if somone had one beyond repair than maybe.

    If it isn't broken...modify it anyway! http://www.DazeCars.com https://galaxieforum.boardhost.com
       •Thread Starter
     

    1/07/2018 12:42 PM  #4

    DC
    Senior 24-7 FYI Addict

    Offline

    From: Marshall, MI
    Registered: 4/01/2013
    Posts: 1,235

    Re: Anyone have a junk 4100 laying around? I need a part

    Just was out in the garage and saw this ring hanging on the pegboard. It is a air cleaner spacer about 5/8 inch thick that I use  to get a little more straight shot into the air horn of the carb. It is basically a tube with the male/female ends to fit the carb and the air cleaner. Would be easy to use on to make what you are after and it was around $13 at Summit a couple of years ago.

     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Anyone have a junk 4100 laying around? I need a part

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.