FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

FYI Ford, Classic Mustang Tech Discussion » MS power brakes & hyrdraulic clutch? » 10/13/2016 9:20 PM

Stangman16
Replies: 1

Go to post

Hello,

I have a '66 Mustang with a T-5 and would like to know if the MS power brake setup will work with a hydraulic clutch?

Thanks,

JW

FYI Ford, Classic Mustang Tech Discussion » '66 Mustang coupe trunk adjustment » 10/29/2013 3:46 PM

Stangman16
Replies: 7

Go to post

Yea I tried loosening the bolts and shifting them over, no luck. Seems Mustangsteve's advice may be working, I just need to give it a few more tries.

Thanks!
 

FYI Ford, Classic Mustang Tech Discussion » '66 Mustang tail light panel install » 10/29/2013 3:45 PM

Stangman16
Replies: 5

Go to post

Yes, I am having issues with the 1/4 panel extensions lining up right with the new quarters I installed, now worse when I try and "dry-fit" everything together before welding. They may be sticking out 1/8"-1/4" right were the tab is on the taillight panel at the outer top corners. If I hammer those tabs flat it'll fit, but i'm not sure if it will look good once I bolt together the lenses...

FYI Ford, Classic Mustang Tech Discussion » '66 Mustang tail light panel install » 10/28/2013 5:12 PM

Stangman16
Replies: 5

Go to post

Ok, will do - thanks, going to do that along with shooting epoxy after I get the filler work complete. The quarter panel sits a little lower then the 1/4 panel extensions - not too happy about it, even though I bought dynacorn quarters.

FYI Ford, Classic Mustang Tech Discussion » '66 Mustang coupe trunk adjustment » 10/28/2013 5:11 PM

Stangman16
Replies: 7

Go to post

New quarters already installed - I did try to fix before welding everything up,but ended up having to do the taillight panel now along with the corner peices that attach to the taillight panel and quarter panels.

It did have the same gap issue with the orginal quarters.

FYI Ford, Classic Mustang Tech Discussion » '66 Mustang tail light panel install » 10/28/2013 1:51 PM

Stangman16
Replies: 5

Go to post

Following along with the install page here at Mustangsteves (thanks Steve!).I'm curious if you just leave the metal bare along the backside of the taillight panel where the ~40 spot welds were at the bottom that I drilled out, and also where it mates up to both quarter panels or if it is advisable to spray something such as weld-thru primer first to both mating surfaces?

Thanks,

FYI Ford, Classic Mustang Tech Discussion » '66 Mustang coupe trunk adjustment » 10/28/2013 1:47 PM

Stangman16
Replies: 7

Go to post

How do you adjust the side to side gap between the quarters on a '66 mustang coupe? I alinged the up/down and front to back, but cannot seem to get the gap set on the sides. I have about a 3/8" gap on the driver side and 1/8" on the pass side.

FYI Ford, Classic Mustang Tech Discussion » '66 mustang 4 wheel disc » 4/05/2013 5:31 PM

Stangman16
Replies: 3

Go to post

also, I did read the Granada install page just now - I don't see where it says you can setup this was for 4 wheel manual discs, but I did see the option of Tee-ing off the front brakes from the rear bowl and using my adjustable proportioning valved for the rear brakes (front bowl).  I gather there is no diferrence in matter if it is 4 wheel disc or front disc / rear drum setup, this should work fine? 

How do you properly adjust the rear brakes using the adjustable proportioning valve?

FYI Ford, Classic Mustang Tech Discussion » '66 mustang 4 wheel disc » 4/05/2013 5:17 PM

Stangman16
Replies: 3

Go to post

I should have double checked before posting... my mistake, I just checked and I have the rear brakes on the adjustable valve coming off the front (smaller) bowl and the front granada discs are just Tee'd coming off the rear bowl on the maverick M/C. Will this still be an okay setup to run with the Mavericak master cylinder for a while?
 

FYI Ford, Classic Mustang Tech Discussion » '66 mustang 4 wheel disc » 4/05/2013 1:48 PM

Stangman16
Replies: 3

Go to post

Almost done installing the Lincoln mk vii rear discs in my '66 coupe using Ultrastang's bracket kit. I have Granada front discs and a maverick master cylinder with the original '66 brake rod. 

Since I'm now going to 4 wheel disc without power, until I purchase MustangSteve's booster setup later this year or next, I'm not quite sure how I should setup using a distribution valve, etc. I have the granada distribution valve and an adjustable proportioning valve currently. I snagged the distribution valve off the '89 lincoln mk vii donor car, assuming I cannot use the Granada proportioning valvce, can I use the lincoln distribution valve along with my adjustable valve and the maverick master cylinder? Or is it a must to switch out the master cylinder?


 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.