Not suuuuure....uhhhh ...may cut my hood just in case

Skip to: New Posts  Last Post
Posted by 6sally6
8/02/2024 11:18 AM 		#1

Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
 
Posted by RTM Online!
8/02/2024 1:30 PM 		#2

Well, you sure would get a lot of attention at the car shows.  lol

 
Posted by wsinsle
8/02/2024 3:45 PM 		#3

Yea but does it have a big cam?

If this forum can't fix it, it isn't broke.
 
Posted by BobE
8/03/2024 6:04 AM 		#4

RTM wrote:

Well, you sure would get a lot of attention at the car shows. lol

And the feedback likely wouldn't be 'positive'! 
 

65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
 
Posted by Nos681
8/03/2024 6:28 AM 		#5

I’m positive that he would get feedback.

 
Posted by TKOPerformance
8/03/2024 9:13 AM 		#6

I'm not a physicist, but I'm pretty sure that wouldn't work unless the engine was mounted 90 degrees from how it would be in a car.  Definitely need a dry sump to make that work (kind of looks like that may be the case). 

 
Posted by Mach1Driver
8/03/2024 10:27 AM 		#7

I'm not sure the floats would be floatin'

 
Posted by Greg B
8/03/2024 10:41 AM 		#8

So that is the legendary Pro form 4 barrel side draft knock off!

If multiple things can go wrong, the one that will go wrong will be the one that causes the most damage.
 
Posted by John Ha
8/03/2024 2:08 PM 		#9

TKOPerformance wrote:

I'm not a physicist, but I'm pretty sure that wouldn't work unless the engine was mounted 90 degrees from how it would be in a car.  

It'd be a great lawnmower engine - mow your yard in 13.8 seconds at 117 MPH.

Founding Member of the Perpetually Bewildered Society
 
Posted by Quicksilver
8/03/2024 6:37 PM 		#10

Bet a plumber had something to do with the design. That looks like something that should be off of a plumbers truck.

Money can't buy happiness. Butt it can buy Car Parts... and that is pretty much the same thing.67 FastBack
 
Posted by Cab4word67
8/03/2024 6:54 PM 		#11

I think the carb needs to go 90 degrees to work

Slammed Big Blue, ran over the varmints that messed with the Stang. Now all is good in the NW
 
Posted by MS
8/04/2024 3:49 PM 		#12

Notice the elbow is not bolted to the intake. But, what if he went EFI and just used the carb as a throttle body?  No fuel in the bowls…

Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 
Posted by GPatrick
8/04/2024 5:00 PM 		#13

Nice way to plumb up a MPFI boosted application with a 90 mm air valve when you have a 4150 square bore intake.  It would probably work better on a slightly shorter intake and if that intake was on a small block Ford.  Here is the Edelbrock version  https://www.edelbrock.com/ultra-low-profile-universal-intake-elbow-90mm-t-b-to-4150-flange-3848.html  Wilson apparently has some good flowing versions of intake and 90 that has much better hood clearance.

 
Posted by 6sally6
8/04/2024 7:56 PM 		#14

MS wrote:

But, what if he went EFI and just used the carb as a throttle body?  No fuel in the bowls…

My thoughts..........
6sally6
 

Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
 
Posted by TKOPerformance
8/05/2024 5:11 AM 		#15

6sally6 wrote:

MS wrote:

But, what if he went EFI and just used the carb as a throttle body? No fuel in the bowls…

My thoughts..........
6sally6
 

I'm sure if someone really wanted to they could make that work, but I foresee a couple issues.  First you'd have to eliminate any kind of progressive linkage for the secondaries.  In order to make a TPS work on it you need everything to open at once with throttle input.  Second, while it may look interesting a 1050 Dominator flows 100cfm less air than a stock 90mm throttle body off a bunch of stock vehicles. 

 


 
Main page
Login
Desktop format