FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    • 1 2  Jump to

       

    12/07/2021 9:45 AM  #26

    Bentworker
    I FYI 24-7

    Offline

    Registered: 9/17/2017
    Posts: 437

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    MS wrote:

    The fuel line is not fastened to anything except the fuel pump and the carb feed line. It touches nothing on the way and is very rigid. Designed to provide clearance for any bolts that would ever need to be removed.

    I had to zoom in and look at it closer.  There was a bend very close to a fastener in one of the pics, I mistook that for a clamp.  Nice work!
     

     

    12/07/2021 1:23 PM  #27

    BobE
    Senior 24-7 FYI Addict

    Offline

    From: White Plains, NY
    Registered: 4/04/2013
    Posts: 2,189

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    MS - looks very good, nice job.

    65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
     

    12/07/2021 1:23 PM  #28

    Rudi
    Senior 24-7 FYI Addict

    Offline

    From: Stuck in the 50's Welland Ca
    Registered: 4/01/2013
    Posts: 3,777

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    Many, many years ago I band sawed and milled a set of rocker cover risers from a 1/2” sheet of 6061 t6 aluminum plate for a friends unmentionable brand of engine.
    He chose to use double gaskets instead of bonding them. AFAIK they did not leak.
    The way Steve did it is much cleaner.

    Good work ain't cheap, Cheap work ain't good!   Simple Man
     

    12/07/2021 4:14 PM  #29

    True74yamaha
    Senior 24-7 FYI Addict

    Offline

    From: Salt Lake City
    Registered: 5/07/2013
    Posts: 2,423

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    Wowie so what's the going rate if I was to ship you my engine and have you build it? With the looks of your skills I would most likely a assume out of my price range. Very nice work.

     

    12/10/2021 2:19 PM  #30

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 11,723

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    True74yamaha wrote:

    Wowie so what's the going rate if I was to ship you my engine and have you build it? With the looks of your skills I would most likely a assume out of my price range. Very nice work.

     
    Figure those valve covers would cost you $600 if you bought them from me, and go from there.  I really am trying to retire from doing engines, but I really enjoy it, and it seems there is always JUST ONE MORE…

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
       •Thread Starter
     

    12/13/2021 2:36 PM  #31

    Rudi
    Senior 24-7 FYI Addict

    Offline

    From: Stuck in the 50's Welland Ca
    Registered: 4/01/2013
    Posts: 3,777

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    Here are the plug wire retainers I made a long time ago.
     Never got around to taking off the ugly oe tab  at the time.

    Last edited by Rudi (12/13/2021 2:38 PM)

    Good work ain't cheap, Cheap work ain't good!   Simple Man
     

    12/14/2021 11:53 AM  #32

    BobE
    Senior 24-7 FYI Addict

    Offline

    From: White Plains, NY
    Registered: 4/04/2013
    Posts: 2,189

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    Rudi wrote:

    Here are the plug wire retainers I made a long time ago.
     Never got around to taking off the ugly oe tab  at the time.

    Rudi - nice work (as usual)

    65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
     

    12/15/2021 8:54 PM  #33

    BILLY WALTON from GEORGIA
    Carrollton, GA Bash Host

    Offline

    From: CARROLLTON GEORGIA
    Registered: 4/14/2013
    Posts: 2,331

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    MS wrote:

    This is the foxbody routing, as was done on Jose’s 5.0 in his 65 fastback. Apparently, he got the last of the foxbody separators.

    I found these come with bolts too

    https://lmr.com/item/LRS-66582K/mustang-factory-style-valve-cover-bolt-and-wire-holder-kit-8

    Last edited by BILLY WALTON from GEORGIA (12/15/2021 8:56 PM)

    Its really me....I fixed my caps lock .
     

    12/16/2021 11:18 AM  #34

    Glens 1965 50
    FYI Addict

    Offline

    From: Tomball,Tx
    Registered: 4/01/2013
    Posts: 262

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    Job well done.

     

    12/17/2021 5:33 PM  #35

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 11,723

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    BILLY WALTON from GEORGIA wrote:

    MS wrote:

    This is the foxbody routing, as was done on Jose’s 5.0 in his 65 fastback. Apparently, he got the last of the foxbody separators.

    I found these come with bolts too

    That is them. Costs more than twice as much to include those bolts that are too short when spacers are added. But, glad to see they are available, as they work well with the pre-1984 POWERED BY FORD valve covers
    https://lmr.com/item/LRS-66582K/mustang-factory-style-valve-cover-bolt-and-wire-holder-kit-8

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
       •Thread Starter
     

    12/17/2021 5:34 PM  #36

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 11,723

    Re: 1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    BILLY WALTON from GEORGIA wrote:

    MS wrote:

    This is the foxbody routing, as was done on Jose’s 5.0 in his 65 fastback. Apparently, he got the last of the foxbody separators.

    I found these come with bolts too

    That is them. Costs more than twice as much to include those bolts that are too short when spacers are added. But, glad to see they are available, as they work well with the pre-1984 POWERED BY FORD valve covers
    https://lmr.com/item/LRS-66582K/mustang-factory-style-valve-cover-bolt-and-wire-holder-kit-8

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
       •Thread Starter
     

     

    1 2  Jump to

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  1/2” billet valve cover spacers blended onto 1984 Mustang 5.0 covers

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.