FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

9/18/2013 11:42 AM  #1


A/C Compressor

I have a bad bearing in my Sanden compressor ('67 Mustang) so I'll be replacing the compressor soon. I know that I will have to get a new dryer also if I change the compressor. I'm being told I should also change the expansion valve. The expansion valve was new a few months ago when I installed the Old Air Products interior kit. Is it REALLY necessary to change the expansion valve? Hate to spend 100 bucks if I don't have to. Thanks,  E.

 

9/18/2013 12:16 PM  #2


Re: A/C Compressor

If the compressor shelled out some parts, I would replace the valve, as it probably was on the receiving end of some of those parts.  If the seals are just worn and it won't make adequate pressure, I would not bother changing the valve.  Just my opinion...


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 

9/18/2013 12:37 PM  #3


Re: A/C Compressor

The compressor is still working and cooling well. A couple of days ago the A/C system suddenly shut down. I found that the fuze had blown. I replaced the fuze and the A/C is blowing cold but the compressor is making a chirping (?) noise when the A/C is on. A normally reliable mechanic friend told me that it was a bad bearing. I thought I would change the compressor before any real damage is done. I'm just not sure what else I need to change out. E. 

     Thread Starter
 

9/18/2013 1:03 PM  #4


Re: A/C Compressor

Be sure the clutch is getting full voltage.  It could be slipping causing the chirp.  You can run a hot wire to straight from the battery to the clutch.  If noise persists, your friend is probably right.  If it goes away, you can replace the clutch or rewire it, and that does not require opening up the system.

I do not think I would mess with the valve.  If it cools well, obviously the valve is not plugged up.

Last edited by MustangSteve (9/18/2013 1:03 PM)


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 

9/18/2013 1:04 PM  #5


Re: A/C Compressor

It may be the replaceable bearing on the clutch. If so, no internals would be involved.

 

9/18/2013 1:20 PM  #6


Re: A/C Compressor

We checked power going to the compressor. It is getting 16 volts. My "normally reliable" mechanic friend told me that he doesn't think the noise is coming from the bearing under the pulley. He thinks there is another bearing where the shaft goes into the body of the compressor and he thinks that is where the noise originates. E.

     Thread Starter
 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.