| ||
| Visit MustangSteve's web site to view some of my work and find details for: FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events |
Offline
What I am up to is making a custom air cleaner for my galaxie engine that just says "different"
I'm converting the air cleaner to have two intake ports. Kind of like an 84 dual snorkel air cleaner if you will. This is nothing new or expirimental. Dodge made a dual snorkel air cleaner, and Chebby made one as well. That said, what I'm looking for is something like this:
I bought two of these to serve as my snorkels. However what bugs me about them is they have the expansion.
If anyone knows of a place where one could get a pipe with the 90 degree flare, but no expansion step up, I'd be very thankful. I'm willing to use what I got, but I really think straight pipe would look better. Or maybe an exhaust shop that can make 90 flares like this.... I've searched and have come up empty.
It will kind of look like this but with two removable snorkels. This one is from a 1962 Galaxie, before emissions and the heat riser.
Edit: I don't know why I didn't think of it earlier, but I emailed Nickson. I will see what they say it they answer.
Last edited by Greg B (Yesterday 1:40 PM)
Offline
I would just cut the flared part off with a cutoff wheel. If it needs to be longer just get the appropriately sized pipe and weld it to the stub with the 90 degree flare on it. You could dress the weld to make it invisible. A little filler, primer and paint and no one would likely know, even if the welds weren't all that great.
Offline

Vibrant makes a plethora of tubing products including oval, in stainless and mild steel.
Offline
TKOPerformance wrote:
I would just cut the flared part off with a cutoff wheel. If it needs to be longer just get the appropriately sized pipe and weld it to the stub with the 90 degree flare on it. You could dress the weld to make it invisible. A little filler, primer and paint and no one would likely know, even if the welds weren't all that great.
I actually thought about doing that. Other than being a pain, I wondered how the scarred up inner pipe would disrupt airflow. Probably negligible, but not worth it if I could find flared straight pipe.
And oddly enough, I also thought of 3d printing some snorkels, and the drawback to that is vibration and heat under the hood.
The current length of the Nickson pipe satisfies what I'm looking for, I hope they tell me they can provide those skipping the expansion.
Offline
Greg B wrote:
TKOPerformance wrote:
I would just cut the flared part off with a cutoff wheel. If it needs to be longer just get the appropriately sized pipe and weld it to the stub with the 90 degree flare on it. You could dress the weld to make it invisible. A little filler, primer and paint and no one would likely know, even if the welds weren't all that great.
I actually thought about doing that. Other than being a pain, I wondered how the scarred up inner pipe would disrupt airflow. Probably negligible, but not worth it if I could find flared straight pipe.
And oddly enough, I also thought of 3d printing some snorkels, and the drawback to that is vibration and heat under the hood.
The current length of the Nickson pipe satisfies what I'm looking for, I hope they tell me they can provide those skipping the expansion.
The disruption to airflow would be too small to be of any significance. If you're that concerned about it you could dress the welds inside the pipes as well using a grinder and/or flap wheel with an extension if necessary. I agree that if a part matching the criteria can be found that's definitely the best solution. I think I'd stick with metal on this too. Plastic long term will get brittle and can crack and fail.
Offline

Is it possible to have a muffler shop expand the small diameter to match the larger diameter?
Not sure if this would make the 90 degree flange too large for the air cleaner housing.
Or could the larger diameter be squeezed back down to the smaller diameter?
Last edited by Nos681 (Yesterday 6:02 PM)
Offline

I had one on my 70 fastback when I was 20. The inlets were 2 or 3” long and a formed a belled flange on the ends by working them with a ballpeen hammer and a file. Looked pretty cool.
Offline

I always liked the 1950’s Cadillac/Oldsmobile air cleaner housing with two air inlets on either side of the air cleaner, just saying. (Check out Speedway Motors)
Offline
I really thought about it last night how I could incorporate that step up expansion in the pipe and it not look stupid. So inspired, I came down this morning and took a few measurements. I came up with this...
From this:
To this:
Now that I got me something I can live with, I got to hunt me some more parts. I hated like heck busting up that piece of unobtanium just for that bracket, but sometimes you gotta do what you gotta do. (I tried selling it on marketplace!)
This turned out easier. I'm going to clean it up, and spot weld it to the bracket.
| REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on. |