FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Borg power steering ..need a littlehelp with the presure line

    • 1 of 1

       

    1/28/2014 5:29 PM  #1

    mainiac1
    FYI Addict

    Offline

    From: Niceville, FL.
    Registered: 4/03/2013
    Posts: 275

    Borg power steering ..need a littlehelp with the presure line

    I have a Borg box in my 66 coupe and now that I have the serpentine brackets figured out I was trying to get lines made locally to go from pump to steering box.. I bought the AN-6 adapters from Borg  to go into the box, and looks like I can buy a Fragola AN-6 female presure line  fitting from Summit, and use an AN-6  to 3/8" barb fitting on return side, but how can I connect it to my pump? I have I think a 92 mustang pump and got a line out of a junkyard 90 something mustang that fits the pump, but the line is too short and the end going into the box was cut off. Was thinking an AN-6 hardline fitting might work on the line going into the pump if the metal tubing is the right size for the ferril that goes with the fitting. Anyone done this please chime in with what you did for your presure line.Thanks,

    Stupid Hurts!...66 coupe, 302, 4 wheel disks...lots of Mods
     

    1/28/2014 7:29 PM  #2

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 11,744

    Re: Borg power steering ..need a littlehelp with the presure line

    The 92 pump is designed to use the swivel type fitting with the o-rings on it.  Earlier pumps (pre-90?) have the compression type fitting.  I think you can change the fitting on the pump body to accept something different. You should be able to put an inverted flare on your tubing and use a flare nut if you change the pump fitting to a female SAE Inv Flare type.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    1/28/2014 10:37 PM  #3

    mainiac1
    FYI Addict

    Offline

    From: Niceville, FL.
    Registered: 4/03/2013
    Posts: 275

    Re: Borg power steering ..need a littlehelp with the presure line

    Thanks Steve, that sounds like an easy part to find!

    Stupid Hurts!...66 coupe, 302, 4 wheel disks...lots of Mods
       •Thread Starter
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Borg power steering ..need a littlehelp with the presure line

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.