FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » c4 auto tranny shifter buttons on 65 mustang

    • 1 of 1

       

    5/05/2014 12:27 AM  #1

    zimmy2nn
    FYI FORD Member

    Offline

    Registered: 5/09/2013
    Posts: 21

    c4 auto tranny shifter buttons on 65 mustang

    I have a 65 mustang coupe with a c4 tranny, I need to replace the buttons on the shifter handel, how is this done? it has a 200 ci 6 cyl. eng. i have the drake kit  but no instructions on how to  install it thanks jim 
     

    Last edited by zimmy2nn (5/05/2014 11:10 AM)

     

    5/05/2014 3:35 PM  #2

    Glens 1965 50
    FYI Addict

    Offline

    From: Tomball,Tx
    Registered: 4/01/2013
    Posts: 279

    Re: c4 auto tranny shifter buttons on 65 mustang

    Are you talking about the two bushings that ride on the pin that goes through the shifter bucket?  If so remove rubber plug to gain acces to the nut that that holds on the shifter handle and remove.  Slide the lower lever/pin from the housing, clean off all old debris.  Inspect the pot metal bushings for excessive wear and install one plastic bushing on each side of the pot metal bushing and reverse steps to re-assemble.  Much easier if the shifter bucket is out of the car.

    Last edited by Glens 1965 50 (5/05/2014 6:12 PM)

     

    5/05/2014 4:01 PM  #3

    ultrastang
    I FYI 24-7

    Offline

    From: Camden, Arkansas
    Registered: 4/01/2013
    Posts: 570

    Re: c4 auto tranny shifter buttons on 65 mustang

    I think the reference is to the T handle. There's a small Allen set screw on the back, near the base where the handle connects to the shift lever. Back the set screw off and pull up on the handle to remove it.

     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  c4 auto tranny shifter buttons on 65 mustang

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.