FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Proportioning Valve Part Needed

    • 1 of 1

       

    5/25/2014 6:24 PM  #1

    everwearman
    FYI FORD Member

    Offline

    Registered: 2/14/2014
    Posts: 17

    Proportioning Valve Part Needed

    I overtightened the flare nut on the proporting valve adapter, this crushed part of the inverted flare cone on the female adapter. Needless to say, it will not seal. I believe the adapter is 5/8" x 3/8" - 24 female inverted flare. I cannot find one like the one shown in picture (with holes below the threads). Do you know where I can find this adapter? Thanks

     

    5/25/2014 6:43 PM  #2

    BobE
    Senior 24-7 FYI Addict

    Offline

    From: White Plains, NY
    Registered: 4/04/2013
    Posts: 2,889

    Re: Proportioning Valve Part Needed

    Try the following venders ... InLine Tube, Classic Tube; plus Weatherhead and Edelman make brake line fittings.

    65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
     

    5/25/2014 9:11 PM  #3

    True74yamaha
    Senior 24-7 FYI Addict

    Offline

    From: Salt Lake City
    Registered: 5/07/2013
    Posts: 2,537

    Re: Proportioning Valve Part Needed

    How about a local hydraulic shop? You maybe able to us a distribution block then for proportioning use and in line one.. Part number 19244448 so I can't get pics to load on here.

    Last edited by True74yamaha (5/25/2014 9:14 PM)

     

    5/26/2014 12:52 PM  #4

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,661

    Re: Proportioning Valve Part Needed

    What kind of valve is it from?  I have some old valves... 

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Proportioning Valve Part Needed

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.