FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Twin Contour fan dimensions

    • 1 of 1

       

    7/01/2013 12:52 PM  #1

    Rudi
    Senior 24-7 FYI Addict

    Offline

    From: Stuck in the 50's Welland Ca
    Registered: 4/01/2013
    Posts: 3,936

    Twin Contour fan dimensions

    I need to ask a favour from anyone out there that has an Contour fan.
    I need the dimensions of the shroud size itself less the mounting tabs.
    Thanks in advance.

    Good work ain't cheap, Cheap work ain't good!   Simple Man
     

    7/01/2013 4:45 PM  #2

    wsinsle
    Senior 24-7 FYI Addict

    Offline

    From: Belle Vernon, PA
    Registered: 4/01/2013
    Posts: 1,698

    Re: Twin Contour fan dimensions

    24 1/4  by 15 3/4

    If this forum can't fix it, it isn't broke.
     

    7/01/2013 5:26 PM  #3

    Rudi
    Senior 24-7 FYI Addict

    Offline

    From: Stuck in the 50's Welland Ca
    Registered: 4/01/2013
    Posts: 3,936

    Re: Twin Contour fan dimensions

    wsinsle wrote:

    24 1/4  by 15 3/4

     
    Thanks a lot for those dimensions. Do you have this system in your car? If you do what engine size is it on and how is it working?

    I forgot to ask what the thickness is at the center. I need to know if there is room between the rad and the front of pulley at the water pump. Any dimension ovr 4 inches and it may not work unless that area can be cut out for clearance.

    I am looking at the Contour fan from Rock Auto at about $100.00, seems like a good deal
    Thanks again.

    Last edited by Rudi (7/01/2013 5:32 PM)

    Good work ain't cheap, Cheap work ain't good!   Simple Man
       •Thread Starter
     

    7/01/2013 6:04 PM  #4

    wsinsle
    Senior 24-7 FYI Addict

    Offline

    From: Belle Vernon, PA
    Registered: 4/01/2013
    Posts: 1,698

    Re: Twin Contour fan dimensions

    Just under 4in thick. Pretty thin, one of reasons people like them, I think. Don't have it on the car, not that far yet. Can't help you with that. With the shroud it should work well.

    If this forum can't fix it, it isn't broke.
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Twin Contour fan dimensions

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.