FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Removal vent window 65 mustang Convt

    • 1 of 1

       

    3/04/2018 4:49 PM  #1

    jon5014ren
    FYI FORD Member

    Offline

    From: Pflugerville, Texas
    Registered: 2/05/2015
    Posts: 32

    Removal vent window 65 mustang Convt

    65 Mustang Convert, 289, 3 speed. Going to do mirror tips to get a good tight seal and would like to redo rubber on vent window. Tried to remove when I updated interior years ago. So my question is: do I need to remove main door glass to get the vent window frame out. Last time I wrestled with the thing for hours and could not figure out how to get out, but I had left the main door glass in. So before I try again I am asking for some advice this time.  Thanks.

     

    3/04/2018 6:38 PM  #2

    6sally6
    Hyper FYIFORD ADDICT

    Offline

    From: Surfside Beach,SC
    Registered: 4/02/2013
    Posts: 6,932

    Re: Removal vent window 65 mustang Convt

    I've found it EZ'er to remove the big glass first.
    Like MS told me once..."cover all the edges of the access holes with tape so it won't cut you if/when you need to reach inside the door."
    Good time to grease and lube and/or replace the window rollers...WYAIT!
    Vacuum iand clean the insides of the doors and lube/adjust the lock mechanism WYAIT.
    6sally6
    PS Door maintenance can be "fun"! 

    Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
     

    3/04/2018 7:19 PM  #3

    MS
    Forum Originator

    Online!

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,489

    Re: Removal vent window 65 mustang Convt

    Remove both of the flanged adjusting bolts as well as the bolts that hold the vent window frame and then slide the vent assembly straight up. It is not required to remove the door glass first.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    3/06/2018 6:46 PM  #4

    jkordzi
    I FYI 24-7

    Offline

    From: Sequim, WA
    Registered: 12/28/2013
    Posts: 927

    Re: Removal vent window 65 mustang Convt

    In addition to what MS said, sometimes it's stuck in there pretty tight and a little judicious leveraging upward from inside the door can help.  Also, you might have someone pry apart the outer and inner skins a bit at the top of the door, using a couple of large flat head screw drivers and some small bits of plywood (to distribute the load and protect the paint).  When you reinstall it, don't tighten the upper bolts too much as you can break the frame. I think MS has a post on installing door glass you should locate.

    Cheap, Fast, Good:  Pick Any Two
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Removal vent window 65 mustang Convt

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.