FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

3/03/2019 10:46 AM  #1


New dual bore master cylinder will not fit. Interferes with shock twr

Hi - I need help and I am sure that I am not the first and that someone here knows the way around this situation.
first: 1966 coupe
331 stroker
Auto trans (AOD - however car was originally 3-speed manual)
Power brakes (originally 10" drums)

I am installing the Mustang Steve front disc conversion for the 12.4" GT rotors/calipers.
At the point where we need to install the new master, prop valve, new lines and hoses.
Problem is that the new master cylinder will not fit. It is about 7.25" long & contacts the shock tower.
Can anyone please point me in the right direction?

Thanks!
 

 

3/03/2019 11:51 AM  #2


Re: New dual bore master cylinder will not fit. Interferes with shock twr

Have NO fear...we got an answer for you!!

Just not me  I have manual front disc-ez BUTT

Mustang Steve knows of a short-er power brake hickey that can make the whole combo fit.
This will keep you bumped-to-the-top.
Welcome to the best forum on the net.
6sally6


Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
 

3/03/2019 8:35 PM  #3


Re: New dual bore master cylinder will not fit. Interferes with shock twr

Thanks for the greeting & the hope there is a solution!

     Thread Starter
 

3/04/2019 2:57 PM  #4


Re: New dual bore master cylinder will not fit. Interferes with shock twr

The orignal 65/66 Mustang power brake booster will only work with the original drum brake master cylinder.  MustangSteve has a retrofit power booster that will work for your car. Either follow the power brake link at the top of the forum title page, or go directly to mustangsteve.com. See the 65/66 power brake conversion kit. The PB-5 kit includes everything you need to properly convert the car to power brakes.


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 

3/09/2019 8:43 AM  #5


Re: New dual bore master cylinder will not fit. Interferes with shock twr

I had to follow up on this post, I figured MS would know. My 67 was converted to power drum brakes
two years ago,I put in a bendix booster,power drum master cylinder,it was a tight fit,with MS's help
I was able I was able to get it in (two pieces).With an engine swap coming up (empty engine bay)
I'm thinking this would be a good time to go to front disc brakes.I have a new extra master cylinder
from my 69 cougar, it seem's to be longer than the power drum master cylinder. I think I have about a
1/4" clearance between the end of the master cylinder (drum brakes) and the shock tower. My
question is did they make two different size power disc master cylinders (overall length)? Or is
there a different set up I would have to use?        THANKS mustang stu

 

3/09/2019 6:12 PM  #6


Re: New dual bore master cylinder will not fit. Interferes with shock twr

The 67-70 disc brake master cylinders were the same part. Two different boosters were used.  Midland-Ross through 69, then a mid year 69 change to Bendix occurred.  All these combinations fit the 67-70 Mustangs.  It was a TIGHT fit, but it fit.
Cars that have been retrofitted to power brakes, even when using all factory parts, do not have the stronger firewall plate the factory used.  Sometimes the installers do not open up the firewall hole to accommodate the booster bellows.  Sometimes they tighten the lower booster studs tighter than the upper studs, bending the thinner firewall and angling the booster downwards.  Since the shock tower gets bigger the lower it exists, any angularity of the booster and master cylinder downward will exacerbate the issue of clearance.
I believe that some of the reproduction master cylinders are a tad longer than the original disc/drum master, but they will all still fit.


 


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 

3/10/2019 9:10 AM  #7


Re: New dual bore master cylinder will not fit. Interferes with shock twr

Dear MS,   Thank's for the input. I will be getting the 67 out of storage (Penna winters) shortly. When
I converted to power brakes,I tried to put the master cylinder,booster in 1 piece,you told me to do it in
2 pieces (A BIG HELP!). I did use a template and opened up the firewall and drilled out 2 holes I believe. It should a lot easier with the engine out. I read Sally's post about the brake switch replacement, in my 40's I got upside down (on driver's seat my, head on the floor mat) and changed the switch out. Now in my almost 70's I can still change the switch, but I have to pull the step sill
plate and driver's seat out.    THANK'S MS!

 

 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.