FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

8/31/2024 5:23 PM  #1


Steve’s Garage Clean Out

TKO600 Tremec five speed, about 15,000 miles on it. Purchased new in 2017/2018  Has a new Pro 5.0 shifter and a heavy duty, couple of years old 10.5” Spec clutch.  Never raced or shifted hard.  $1,850 with the original shifter, or $1,950 with a near new Pro 5.0 shifter on it.  SOLD

Strange aluminum 9” center section. 3.70:1 Traction Lock. 31 spline. 1350 u-joint size.  I had it built new and used for a couple of bash trips. Changed it for a 3.50:1. Was in my 66.  $1,000

Steel 3” drive shaft correct length for TKO600 or T5.
1350 ujoint size (there are 1310/1350 crossover ujoints available from Summit). No tranny yoke with it.  $200

9” rear end housing for 65-66.  A narrowed assembly with big bearing ends and spring perches to fit 65-66.  No axles $300. REDUCED TO $200

Pair of 15x7 Magnum 500 chrome/black wheels. They have 2” center hole, correct for 69-70.  One has a correct cap.  Other one no cap. Pretty good chrome. Driver quality but they do roll straight.  $200. SOLD

I have a garage full of stuff I need to clear out.  Ask if you need something. 
Located in Canyon Lake, Tx 78133

Holley 750 carb off my 427.  Has new center pivot bowls with Cobra Jet/Boss style fuel lines. Rebuilt early 2024. Vacuum secondary, electric choke.  Good running carb. Removed from service 8-29-2024. $350. SOLD

T-5 transmission with bellhousing for 289/302/351
$850. I bought it as a rebuilt tranny, truth be unknown, and never used it. Includes stock shifter.

Last edited by MS (11/03/2024 4:55 PM)


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 

11/04/2024 2:29 PM  #2


Re: Steve’s Garage Clean Out

Hello can you tell me more about the strange center section , which brand of gear set and traction lock are installed, also which strange housing is it?
Also curious on the 9" housing that is narrowed, how much has it been narrowed?

Rich
 

Last edited by Radon30 (11/04/2024 2:30 PM)

 

Yesterday 10:05 PM  #3


Re: Steve’s Garage Clean Out

Strange aluminum 9” housing with big bearing. It has a Ford traction lock in it with 31 spline axles  3150 short yoke. Strange gears. 3.50 ratio.

The narrowed 9” housing is 57-1/4” wide to fit 65-66 stock width or 67-70 as 2” narrowed. Fits stock spring width spacing.  Has big 3.150” bearing ends.


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     Thread Starter
 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.