FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » back up switch wiring

    • 1 of 1

       

    10/17/2014 8:37 PM  #1

    retired 65
    I FYI 24-7

    Offline

    From: nixa, mo.
    Registered: 4/02/2013
    Posts: 336

    back up switch wiring

    Can someone tell me how the back-up switch wiring is routed on a '65 with 4 spd manual trans?  Where does the wire go through the floor to the switch at the trans. shifter?  Thanks Jerry

    "when I drop something, it always goes to center of the car"
     

    10/18/2014 9:21 AM  #2

    BobE
    Senior 24-7 FYI Addict

    Offline

    From: White Plains, NY
    Registered: 4/04/2013
    Posts: 2,210

    Re: back up switch wiring

    If memory serves me, there is a hole next the the shifter opening (on the left side) in floor where this wire passes through.

    65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
     

    10/18/2014 9:47 AM  #3

    Glens 1965 50
    FYI Addict

    Offline

    From: Tomball,Tx
    Registered: 4/01/2013
    Posts: 262

    Re: back up switch wiring

    The area is directly to the rear of the shifter.  Lift the carpet and you will see the indention.

     

    10/18/2014 8:19 PM  #4

    retired 65
    I FYI 24-7

    Offline

    From: nixa, mo.
    Registered: 4/02/2013
    Posts: 336

    Re: back up switch wiring

    thanks for the info.  My complete floorboard was replaced, so I don't have any holes or indentions to go buy.  I will make a hole around the shifter and run it down to the shifter.  I suppose the wire runs along the top of the tunnel before going through the floorboard.  Jerry

    "when I drop something, it always goes to center of the car"
       •Thread Starter
     

    10/19/2014 1:46 PM  #5

    MWM
    I FYI 24-7

    Offline

    Registered: 4/01/2013
    Posts: 423

    Re: back up switch wiring

    Jerry
    You are correct on the wiring run along the console back to the firewall. You will need to make an indentation as there is a rubber grommet where the wires go through the floor pan. The rubber will make a bump in the carpet. Otherwise just notch the carpet around the rubber grommet
    Good luck

     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  back up switch wiring

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.