FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Dumb Queston? Jack Stand placement

    • 1 of 1

       

    5/30/2013 12:30 PM  #1

    Novi Rick
    FYI Addict

    Offline

    From: Novi, Michigan
    Registered: 4/01/2013
    Posts: 148

    Dumb Queston? Jack Stand placement

    Where is the best / safest place for jacking and jack stand placement on a 65 Fastback front and rear?  To change a tire there are notches on the rocker pinch weld but is that where jack stands should go? I need to get all four off the ground to get under for some work and I don't need it falling on me.

    Remember now - there are no dumb questions!

    Thanks!

     

    5/30/2013 12:36 PM  #2

    Michael H.
    I FYI 24-7

    Offline

    From: Laurel, MS
    Registered: 4/01/2013
    Posts: 869

    Re: Dumb Queston? Jack Stand placement

    I like to place them under the frame rails in the front and under the axle in the rear.

     

    5/30/2013 2:07 PM  #3

    Derek
    I FYI 24-7

    Offline

    From: Eatonton GA
    Registered: 4/01/2013
    Posts: 549

    Re: Dumb Queston? Jack Stand placement

    Agree . Or sometimes if I need it up higher I'll jack up the front and slide ramps under the front tires. I don't like trying to drive up on them, creeps me out!

    It's hard to type "funny"
     

    5/30/2013 3:02 PM  #4

    Pete M
    FYI FORD Member

    Offline

    Registered: 4/01/2013
    Posts: 76

    Re: Dumb Queston? Jack Stand placement

    It's funny you say that, Derek!  I feel the same way.  Not so much with an automatic transmision cars, but with the clutch is a whole OTHER story!

     

    5/30/2013 3:06 PM  #5

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,155

    Re: Dumb Queston? Jack Stand placement

    Just DO NOT place them under the floor beams.  They are not thick enough to support the weight without bending.  I hope you have the large 3 ton jack stands.  You can put them under the frame rails right under the front bumper bolts.  In rear, there is not really a good place other than under the axle.  If that doesn't work due to the nature if the work you are doing, the 6" of level frame rail beside the spring eye bolt will work, but it will bend if you do not spread the load over some wide jackstand cradles.

    The 4 places where the stock scissor jack fit under the rocker panels will work very well, since they are designed for that purpose.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    5/30/2013 5:10 PM  #6

    T. McG/393
    FYI Addict

    Offline

    From: Central IL.
    Registered: 4/01/2013
    Posts: 126

    Re: Dumb Queston? Jack Stand placement

    I built a support to fit on a floor jack to raise the front of my '66 car and place floor jacks under it.
    Sroll to the bottom of the linked page for pics.   http://www.tm66mustang.com/photo_album3.html

    Hosted Mustang Steve Birthday Bash 2009        http://www.tm66mustang.com
     

    5/30/2013 5:32 PM  #7

    josh-kebob
    Senior 24-7 FYI Addict

    Offline

    From: Madison, AL
    Registered: 4/06/2013
    Posts: 2,902

    Re: Dumb Queston? Jack Stand placement

    i like that terry, will you build me one and ship it for free!!!

     

    5/30/2013 6:36 PM  #8

    T. McG/393
    FYI Addict

    Offline

    From: Central IL.
    Registered: 4/01/2013
    Posts: 126

    Re: Dumb Queston? Jack Stand placement

    But the fun is in building your own. 

    Hosted Mustang Steve Birthday Bash 2009        http://www.tm66mustang.com
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Dumb Queston? Jack Stand placement

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.