FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » What, If Any, Bolt Goes Here?

    • 1 of 1

       

    1/20/2021 9:21 PM  #1

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,662

    What, If Any, Bolt Goes Here?

    So I'm bolting up my steering column and can't remember or find a bolt that goes where the yellow dot in the pictures. I've got all the other holes accounted for including the hole directly across from the yellow dot.



    Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering, factory AC.
     

    1/20/2021 9:48 PM  #2

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,662

    Re: What, If Any, Bolt Goes Here?

    I recieved info that the hole in question is not used on a 69 Mustang. So I think I'll go with that and button up the dash.

    Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering, factory AC.
       •Thread Starter
     

    1/20/2021 11:49 PM  #3

    6sally6
    Hyper FYIFORD ADDICT

    Offline

    From: Surfside Beach,SC
    Registered: 4/02/2013
    Posts: 6,855

    Re: What, If Any, Bolt Goes Here?

    Naaaaaaaaaaaaaa.....'fits bolted to the bottom of the dash  all those others are jus X-tree. Mighta fell out leaving the assembly line  in 69!  FoMoCo was still slinging 'em out then and quality control was just a 'suggestion'!

    6s6

    Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
     

    1/21/2021 7:07 PM  #4

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,662

    Re: What, If Any, Bolt Goes Here?

    Well, I was informed of the correct info today. That bolt and the one directly left of it in the pic, take a 5/16 bolt into a captive nut located on the lower dash. My image of the Osborn manual is from the Chassis, not the Body Assembly manual, which has the proper diagram.



    Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering, factory AC.
       •Thread Starter
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  What, If Any, Bolt Goes Here?

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.