FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?



3/24/2021 11:35 AM  #1


Bradster Archive - Gauges - How they Work

https://i.ibb.co/BywyL9L/Gauges.jpg


Founding Member of the Perpetually Bewildered Society
 

3/24/2021 12:14 PM  #2


Re: Bradster Archive - Gauges - How they Work

Here's some supplemental information I've found since - maybe it will be useful

https://i.ibb.co/sv6tcMn/Internals-1.jpg

https://i.ibb.co/DQ1r7XQ/Internals-2.jpg


Founding Member of the Perpetually Bewildered Society
     Thread Starter
 

7/17/2021 5:36 AM  #3


Re: Bradster Archive - Gauges - How they Work

While the drawing above is very nicely done, and probably the best description of how it works that I've seen, butĀ  it is not quite accurate. It says that on high the circuit would have 225mA. The IVR (Instrument Voltage Regulator) supplies an average of 5VDC, So using Ohms Law, R= 5V /.225A= 22.22 ohms. Since the sensor is 10 ohms of that total, 22.22 - 10 = 12.22 ohms for the gauge heater. That's a reasonable number, as I have measured 12.4 and 12.8 ohms resistance for the gauge heater.
Here is where the first problem arises- The Ford Shop Manual says that the sensors are variable resistors that range from 10 ohms on high to 73 ohms on low, not 75 ohms. So lets add 12.22 ohms for the heater to 73 ohms for a total of 12.22+73=85.22 ohms when on high. The amperage would then be 5V / 85.22 Ohms = .059 amps, not .006 amps. It looks like they missed it by a decimal point. Its closer to 60mA (.060A) instead of 6mA (.006A).
It may not seem like much, but in electronics it makes all the difference in the world https://cdn.boardhost.com/emoticons/cool.png
.

Last edited by Mach1Driver (7/17/2021 12:42 PM)

 

7/21/2021 12:06 AM  #4


Re: Bradster Archive - Gauges - How they Work

Hey Terry, welcome to the forum. This place has THE friendliest people, bar none. Btw, I used to be rpm here, but a couple of bearing issues fixed that.


Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering.
 

7/22/2021 5:41 PM  #5


Re: Bradster Archive - Gauges - How they Work

Bearing Bob...ok, gotta remember that- I like your RPM avatarĀ https://cdn.boardhost.com/emoticons/happy.png

 

Board footera

 

Powered by Boardhost. Create a Free Forum


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.