FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » I now have my new Bilstein street valve and 1 inch sway bar on

    • 1 2  Jump to

       

    10/27/2021 6:24 PM  #26

    BILLY WALTON from GEORGIA
    Carrollton, GA Bash Host

    Offline

    From: CARROLLTON GEORGIA
    Registered: 4/14/2013
    Posts: 2,431

    Re: I now have my new Bilstein street valve and 1 inch sway bar on

    BobE wrote:

    BILLY WALTON from GEORGIA wrote:

    Rudi wrote:

    If you want to experience “snap oversteer” put a rear sway bar on an early Mustang.
    After your car gets pulled out of the ditch, hopefully damage free, I’m sure you will remove it.
    Ford put them on some early Mustangs but I think they were on big blocks with the rest of the suspension tuned for it.

    Same thing I have always heard.
     

    Years ago, I bought a rear sway bar for my 65, and was then sternly advised not to install it, so I didn't install it.  Still have it if anyone is interested, but I lost the mounting hardware somewhere along the way. 
     

    I got the front one you had on your car  on the front of my wrecked car ....It is a little bent now.

    Its really me....I fixed my caps lock .
     

    10/29/2021 1:29 PM  #27

    Mochaman
    Senior 24-7 FYI Addict

    Offline

    From: Royse City, Texas
    Registered: 4/02/2013
    Posts: 1,487

    Re: I now have my new Bilstein street valve and 1 inch sway bar on

    I have noticed zero corner issues with my 65 and have never been in a ditch. It is very flat around corners. 

     

    10/31/2021 5:37 AM  #28

    BILLY WALTON from GEORGIA
    Carrollton, GA Bash Host

    Offline

    From: CARROLLTON GEORGIA
    Registered: 4/14/2013
    Posts: 2,431

    Re: I now have my new Bilstein street valve and 1 inch sway bar on

    Mine hugged the curves good too.

    Its really me....I fixed my caps lock .
       •Thread Starter
     

     

    1 2  Jump to

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  I now have my new Bilstein street valve and 1 inch sway bar on

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.