FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Anybody on here running the adjustable Monte Carlo bars?

    • 1 of 1

       

    12/31/2021 10:33 AM  #1

    BILLY WALTON from GEORGIA
    Carrollton, GA Bash Host

    Offline

    From: CARROLLTON GEORGIA
    Registered: 4/14/2013
    Posts: 2,431

    Anybody on here running the adjustable Monte Carlo bars?

    I was concerned about the movement looks like Heim joints....but could see an advantage of being able to remove it when need to remove engine and what are the advantages of the curved vs. straight bar I I know to clear some distributors and air cleaners.

    https://www.summitracing.com/parts/gls-ts-8






     

    Last edited by BILLY WALTON from GEORGIA (12/31/2021 10:40 AM)

    Its really me....I fixed my caps lock .
     

    12/31/2021 11:28 AM  #2

    Rudi
    Senior 24-7 FYI Addict

    Offline

    From: Stuck in the 50's Welland Ca
    Registered: 4/01/2013
    Posts: 3,974

    Re: Anybody on here running the adjustable Monte Carlo bars?

    Heim joints useless in that application, might as well have less expensive clevis and pins if you want easy removal.
    Solid is a better option.
    I don’t use one, just sayin

    Last edited by Rudi (12/31/2021 11:29 AM)

    Good work ain't cheap, Cheap work ain't good!   Simple Man
     

    12/31/2021 1:05 PM  #3

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,654

    Re: Anybody on here running the adjustable Monte Carlo bars?

    I've bought a couple of and built a couple of Monte Carlo bars. If the only forces the bar is experiencing is compression, I don't know why the heim end one won't work just fine. Obviously the straight one will be the strongest, but how strong is strong enough? I needed a slightly bent bar to clear the taller Mallory dual point distributor, so I put a 10 degree bend in a piece of 1 inch x .125 wall 4130, welded on left and right tube adapters and used clevis ends.





    I've got a hillbilly quick release where after I loosen the jamb nut and twist the bar slightly, the pin comes right out.



    I'm pretty sure Mochman uses that same bar BILLY linked. For $125 it's hard to beat.

    Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering, factory AC.
     

    12/31/2021 2:03 PM  #4

    Bentworker
    I FYI 24-7

    Offline

    Registered: 9/17/2017
    Posts: 472

    Re: Anybody on here running the adjustable Monte Carlo bars?

    Mine is one giant welded together trapezoid that connects the towers to each other and the Cowl.  Takes 20 minutes to pull it out.  One of the things I find handy about them is they make a nice support to grab on to when leaning into the engine compartment.  If nothing else the bar made my carburetor tuning project easier.  Sure beats trying to support yourself on a hot engine.

    The heim joint ones creep me out a bit, but I see why they are built that way.  Far easier to ship, and easy to adjust to fit a 50+ year old car that has had bumps and bruises along the way.  Maybe weld one up if you have the fabrication tools handy?

     

    12/31/2021 3:12 PM  #5

    6sally6
    Hyper FYIFORD ADDICT

    Offline

    From: Surfside Beach,SC
    Registered: 4/02/2013
    Posts: 6,852

    Re: Anybody on here running the adjustable Monte Carlo bars?

    Why 're-invent' the wheel (or bar!)
    Axe yo self......"how many times am I gonna be pull'in-the-engine!?" Twice....once....ever?? (I didn't think so...)
    When doing the prep for an "engine pull"....one piece export bar....solid Monte Carlo bar...radiator support w/ radiator..disconnect fuel lines...electrical wires....fight'n with headers!!....etc.
    You can see the solid Monte Carlo that Carroll Shelby introduced way back in the early sixties ain't a deal breaker as far as time saved when gett'in ready to 'pull-da-mow-der'!
    What an extra 10 minutes.... compared to the heim joint  abortion that does work as well as the solid bar??! (and is more expensive!)
    6sally6
    PS....You know.....you can put a big old snotty camshaft in WITHOUT  pulling the 'mow-der!
    jUS SAY'IN!

    Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
     

    12/31/2021 4:08 PM  #6

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,253

    Re: Anybody on here running the adjustable Monte Carlo bars?

    The way Bearing Bob did it, with the heim joints flat in line with the bar’s center, is the strongest way.

    The ones where the heim joint mount is elevated and tightening the joint simply bends whatever the mount is welded or bolted to is the problematic method.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    12/31/2021 4:43 PM  #7

    Rudi
    Senior 24-7 FYI Addict

    Offline

    From: Stuck in the 50's Welland Ca
    Registered: 4/01/2013
    Posts: 3,974

    Re: Anybody on here running the adjustable Monte Carlo bars?

    MS wrote:

    The way Bearing Bob did it, with the heim joints flat in line with the bar’s center, is the strongest way.
    In Canada we call those clevises
    In Texas and Bako the nomenclature may differ.😁
    .

     

    Good work ain't cheap, Cheap work ain't good!   Simple Man
     

    12/31/2021 5:21 PM  #8

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,253

    Re: Anybody on here running the adjustable Monte Carlo bars?

    Rudi wrote:

    MS wrote:

    The way Bearing Bob did it, with the heim joints flat in line with the bar’s center, is the strongest way.
    In Canada we call those clevises
    In Texas and Bako the nomenclature may differ.😁
    .

     

     
    Rudi, you are absolutely correct. Clevis, it is.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    12/31/2021 5:33 PM  #9

    Rudi
    Senior 24-7 FYI Addict

    Offline

    From: Stuck in the 50's Welland Ca
    Registered: 4/01/2013
    Posts: 3,974

    Re: Anybody on here running the adjustable Monte Carlo bars?

    One way a Hiem joint would work if it was supported by a mounting tab on either side, but still the last photo from BB is the simplest.

    Good work ain't cheap, Cheap work ain't good!   Simple Man
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Anybody on here running the adjustable Monte Carlo bars?

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.