FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Is this enough cam for Sal? 😉

    • 1 of 1

       

    3/01/2022 4:52 AM  #1

    Toploader
    Senior 24-7 FYI Addict

    Offline

    Registered: 4/15/2013
    Posts: 1,640

    Is this enough cam for Sal? 😉

    1964-1/2 D Code Coupe - 289 V8, 4 Speed Toploader, 3.00 ratio rear, Autolite 4100 Carb, 15" tires, Pertronix ignition
     

    3/01/2022 5:58 AM  #2

    TKOPerformance
    Hyper FYIFORD ADDICT

    Offline

    From: Newark, DE
    Registered: 12/15/2014
    Posts: 7,498

    Re: Is this enough cam for Sal? 😉

    Nah, the blower is too small, or there should be a second, larger blower below it.

     

    3/01/2022 9:44 AM  #3

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,253

    Re: Is this enough cam for Sal? 😉

    That car is doing what it does best.

    Sitting still

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    3/01/2022 10:57 AM  #4

    Greg B
    Senior 24-7 FYI Addict

    Offline

    Registered: 4/01/2013
    Posts: 1,696

    Re: Is this enough cam for Sal? 😉

    Could be used as the official bash hot dog cooker.   Like that one festival that uses the 1909 case steam tractor to boil ears of corn.

    If multiple things can go wrong, the one that will go wrong will be the one that causes the most damage.
     

    3/02/2022 6:12 AM  #5

    Toploader
    Senior 24-7 FYI Addict

    Offline

    Registered: 4/15/2013
    Posts: 1,640

    Re: Is this enough cam for Sal? 😉

    Perhaps I was being a tad conservative with the first car. Maybe this one has enough cam for Sal 🥳



    Last edited by Toploader (3/02/2022 6:14 AM)

    1964-1/2 D Code Coupe - 289 V8, 4 Speed Toploader, 3.00 ratio rear, Autolite 4100 Carb, 15" tires, Pertronix ignition
       •Thread Starter
     

    3/02/2022 9:35 AM  #6

    6sally6
    Hyper FYIFORD ADDICT

    Offline

    From: Surfside Beach,SC
    Registered: 4/02/2013
    Posts: 6,852

    Re: Is this enough cam for Sal? 😉

    Luv the Mustang Steve front  pulley drive/acessories !

    I would need a co-pilot for right-hand turns!!!! (any volunteers?!)
    6sal6

    Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
     

    3/02/2022 9:50 AM  #7

    BobE
    Senior 24-7 FYI Addict

    Offline

    From: White Plains, NY
    Registered: 4/04/2013
    Posts: 2,642

    Re: Is this enough cam for Sal? 😉

    Built for auto cross?
    And what engine is hiding under the three superchargers?

    65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
     

    3/02/2022 11:50 AM  #8

    TKOPerformance
    Hyper FYIFORD ADDICT

    Offline

    From: Newark, DE
    Registered: 12/15/2014
    Posts: 7,498

    Re: Is this enough cam for Sal? 😉

    BobE wrote:

    Built for auto cross?
    And what engine is hiding under the three superchargers?

    2.3 DOHC.  No room for anything else.  But it makes 15HP per cubic inch, so...

     

    3/03/2022 10:53 AM  #9

    BobE
    Senior 24-7 FYI Addict

    Offline

    From: White Plains, NY
    Registered: 4/04/2013
    Posts: 2,642

    Re: Is this enough cam for Sal? 😉

    TKOPerformance wrote:

    BobE wrote:

    Built for auto cross?
    And what engine is hiding under the three superchargers?

    2.3 DOHC.  No room for anything else.  But it makes 15HP per cubic inch, so...

    LOL
     

    65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Is this enough cam for Sal? 😉

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.