FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » What cam are ya using?

    • 1 2  Jump to

       

    4/21/2022 12:03 PM  #26

    Mustsed
    FYI FORD Member

    Offline

    From: Antalya / Turkey
    Registered: 3/30/2022
    Posts: 56

    Re: What cam are ya using?

    Hi everybody,

    My '67 Hardtop with:
    SBF 5.0 EFI - Hypereutetic .020 over pistons,
    E7 heads gasket matched and slightly ported/polished,
    Explorer intake manifold,
    Scorpion roller rockers,
    e303 camshaft
    T5 WC tranny
    3.73;1 geras in a Jaguar IRS
    17" Torque Thrut 2 wheels with 275/40/17 rear and 235/45/17 up front.

    Well, more then enough for a 55 year old car! 

    Mustsed

    Last edited by Mustsed (4/21/2022 12:04 PM)

     

    4/22/2022 12:06 AM  #27

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,653

    Re: What cam are ya using?

    Mustsed wrote:

    Hi everybody,

    My '67 Hardtop with:
    SBF 5.0 EFI - Hypereutetic .020 over pistons,
    E7 heads gasket matched and slightly ported/polished,
    Explorer intake manifold,
    Scorpion roller rockers,
    e303 camshaft
    T5 WC tranny
    3.73;1 geras in a Jaguar IRS
    17" Torque Thrut 2 wheels with 275/40/17 rear and 235/45/17 up front.

    Well, more then enough for a 55 year old car! 

    Mustsed

    You had me at Jag IRS. Do tell, and show please.

    Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering, factory AC.
     

    4/22/2022 11:53 AM  #28

    Mustsed
    FYI FORD Member

    Offline

    From: Antalya / Turkey
    Registered: 3/30/2022
    Posts: 56

    Re: What cam are ya using?

    Hi BB,

    Here is a link to other Mustangs with IRS. The first two are done by me. Almost same setup as the one on my '67. Have done 7 of this swaps and the owners (me included) are happy with it! PM me your email and i will send you other pictures of the setup.

    Mustsed

    https://dazecars.com/dazed/JaguarIRSSuccess.html

    Last edited by Mustsed (4/22/2022 11:56 AM)

     

    4/22/2022 3:15 PM  #29

    Nos681
    Senior 24-7 FYI Addict

    Offline

    From: Atlantic Mine, Michigan
    Registered: 7/14/2016
    Posts: 3,331

    Re: What cam are ya using?

    Nice work Mustsed.

    I’m liking the non-Sally approved cams.😁
    Especially the lower rpm’s and torque.

    Between the stock 92 Mustang cam and Edelbrock 2122 cams in 5.0L and 289 respectively, I like the vacuum friendly cams.  Both have nice street manners….I must be getting old.😂

       •Thread Starter
     

     

    1 2  Jump to

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  What cam are ya using?

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.