FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Looking for a hi-po Air breather for my 65 but it is a 2bbl

    • 1 of 1

       

    6/09/2022 10:22 PM  #1

    BILLY WALTON from GEORGIA
    Carrollton, GA Bash Host

    Offline

    From: CARROLLTON GEORGIA
    Registered: 4/14/2013
    Posts: 2,431

    Looking for a hi-po Air breather for my 65 but it is a 2bbl

    I put a Straight Monte Carlo bar and the factory Breather don't fit anymore. wasn't sure if the y made a base for the hi-po breather I googled  around looking and did not rally see one....thought maybe it was the same as a 4bbl but don't have a 4bbl breather to try.

    Its really me....I fixed my caps lock .
     

    6/10/2022 5:26 AM  #2

    Texas!
    FYI Addict

    Offline

    Registered: 6/27/2014
    Posts: 231

    Re: Looking for a hi-po Air breather for my 65 but it is a 2bbl

    2V and 4V Autolite and Holley carbs use the same base.

     

    6/10/2022 8:19 PM  #3

    BILLY WALTON from GEORGIA
    Carrollton, GA Bash Host

    Offline

    From: CARROLLTON GEORGIA
    Registered: 4/14/2013
    Posts: 2,431

    Re: Looking for a hi-po Air breather for my 65 but it is a 2bbl

    Texas! wrote:

    2V and 4V Autolite and Holley carbs use the same base.

    Good to know I knew it looked the same size but wasn't sure.
     

    Its really me....I fixed my caps lock .
       •Thread Starter
     

    6/11/2022 7:49 AM  #4

    mjacobs
    FYI FORD Member

    Offline

    From: Crossville Tn
    Registered: 2/07/2014
    Posts: 91

    Re: Looking for a hi-po Air breather for my 65 but it is a 2bbl

    i have a Summit Racing Air Filter assemble on my 66
    https://www.summitracing.com/parts/sum-239433

    302 with Perfomer 289 intake, Phenolic 3/8 spacer plus a Ford Spacer that has PVC port on it. Total spacing from base of intake carb mounting flange to Summit 600cfm carb is 1 1/2 inches. Air filter assemble is 14". Clears my hood and straight monticarlo bar

    thanks

     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Looking for a hi-po Air breather for my 65 but it is a 2bbl

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.