FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » TV Geometry on EFI throttle body

    • 1 of 1

       

    9/30/2023 10:46 AM  #1

    gkm24
    FYI Addict

    Offline

    From: Winchester, Hampshire, England
    Registered: 6/08/2013
    Posts: 108

    TV Geometry on EFI throttle body

    So I finally have my 66  EFI running lovely with the new gauges in the dash. Its time to take it to get the steering alignment set up but I just went to connect the TV cable to the throttle linkage and see that I need to make up some sort of bracket as if I just connect it the the linkage, the tv cable will stop me getting full throttle. Anyone got a pattern for a bracket or picture of where to connect the TV cable? The TV cable I have is a Lokar cable.
    Thanks for any help.

     

    9/30/2023 11:16 AM  #2

    Rudi
    Senior 24-7 FYI Addict

    Offline

    From: Stuck in the 50's Welland Ca
    Registered: 4/01/2013
    Posts: 3,960

    Re: TV Geometry on EFI throttle body

    Do you mean like this?

    Good work ain't cheap, Cheap work ain't good!   Simple Man
     

    9/30/2023 11:22 AM  #3

    gkm24
    FYI Addict

    Offline

    From: Winchester, Hampshire, England
    Registered: 6/08/2013
    Posts: 108

    Re: TV Geometry on EFI throttle body

    Thanks, Yes but mine is EFI from a 95 Fox body so need the EFI set up.

       •Thread Starter
     

    9/30/2023 12:02 PM  #4

    Rudi
    Senior 24-7 FYI Addict

    Offline

    From: Stuck in the 50's Welland Ca
    Registered: 4/01/2013
    Posts: 3,960

    Re: TV Geometry on EFI throttle body

    It’s the same operational principle.
    TV cable attachment point has to be equidistant to and on the same plane with the throttle actuator mounting point.
    As for the bracket , it can be a simple angle bracket mounted anywhere there is a straight pull on the throttle arm.

    Good work ain't cheap, Cheap work ain't good!   Simple Man
     

    10/01/2023 8:47 AM  #5

    Nos681
    Senior 24-7 FYI Addict

    Offline

    From: Atlantic Mine, Michigan
    Registered: 7/14/2016
    Posts: 3,324

    Re: TV Geometry on EFI throttle body



    This is a bracket for stock EFI.
    The throttle cable and the the TV cable mount on this bracket.
    Same bracket is used on T5/AOD transmission.

    Last edited by Nos681 (10/01/2023 8:48 AM)

     

    10/01/2023 10:29 AM  #6

    gkm24
    FYI Addict

    Offline

    From: Winchester, Hampshire, England
    Registered: 6/08/2013
    Posts: 108

    Re: TV Geometry on EFI throttle body

    Thank you both for your help.
     

       •Thread Starter
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  TV Geometry on EFI throttle body

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.