FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Shaker on a 66 mustang ?

    • 1 of 1

       

    6/02/2024 10:35 AM  #1

    Evan
    FYI FORD Member

    Offline

    From: San Diego
    Registered: 4/14/2013
    Posts: 72

    Shaker on a 66 mustang ?

    Hey there everyone. Hope y’all have been doing good. Been keeping my head down working allot on my 66 mustang and just wrapped up most of my interior re do . Just need to do new glove box door and gauges. Here’s a picture of the interior

    For now though I’m moving to the hood. A long time ago when I was younger I sold my stock hood and got a 3” cowl induction fiberglass one. It’s ok but it just doesn’t look right to me now. I just picked up a re pro steel hood for pretty cheap and I’ve been playing with the idea of doing a shaker hood scoop on it. I’ve already got the shaker set up and was looking at ordering the template to  try and cut the hole with. Has anyone ever done this here?  If so any pieces of advice you could give would be appreciated.

     

    6/02/2024 11:23 AM  #2

    BobE
    Senior 24-7 FYI Addict

    Offline

    From: White Plains, NY
    Registered: 4/04/2013
    Posts: 2,597

    Re: Shaker on a 66 mustang ?

    Seems to me that someone did a shaker scoop on a 65-66 Mustang and posted some pictures.  Suggest trying the 'search' feature.  

    65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
     

    6/02/2024 11:28 AM  #3

    Evan
    FYI FORD Member

    Offline

    From: San Diego
    Registered: 4/14/2013
    Posts: 72

    Re: Shaker on a 66 mustang ?

    Thanks. I was looking and haven’t seen it yet. I’ll keep searching.

       •Thread Starter
     

    6/02/2024 12:41 PM  #4

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,619

    Re: Shaker on a 66 mustang ?

    Terry has one on his fb

    Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering, factory AC.
     

    6/02/2024 2:47 PM  #5

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,186

    Re: Shaker on a 66 mustang ?

    Different Terry, but Terry McGovern put one on his 66 fastback many years ago.  Terry has since passed and the car was sold.  It looks pretty good, but long term I think
    Leaving the outward appearance of a Classic Mustang as close to stock as possible is best. But then, I am an
    Old fart, set in my ways, and opinionated.  At least this scoop thing is something that can very easily be reversed. It is, in my opinion, at least 10,000 percent better than a Chevy cowl hood, though. Using more modern Ford stuff to modify a Mustang is way better than installing something that never belonged on any Mustang.
    From someone who has owned several 70 Mustangs with shaker scoops, be advised they are a pain in the butt to remove to adjust the carb, and your engine WILL get rain water on it. The worst thing was the distributor getting stuck in the block due to corrosion. 
    If you do it, coat the distributor body with anti-seize where it touches the block, both above and below the o-ring.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    6/02/2024 4:20 PM  #6

    Ron68
    Senior 24-7 FYI Addict

    Offline

    From: Mukilteo, Washington
    Registered: 4/01/2013
    Posts: 1,549

    Re: Shaker on a 66 mustang ?

    MS wrote:

    Different Terry, but Terry McGovern put one on his 66 fastback many years ago. Terry has since passed and the car was sold. It looks pretty good, but long term I think
    Leaving the outward appearance of a Classic Mustang as close to stock as possible is best. But then, I am an
    Old fart, set in my ways, and opinionated. At least this scoop thing is something that can very easily be reversed. It is, in my opinion, at least 10,000 percent better than a Chevy cowl hood, though. Using more modern Ford stuff to modify a Mustang is way better than installing something that never belonged on any Mustang.
    From someone who has owned several 70 Mustangs with shaker scoops, be advised they are a pain in the butt to remove to adjust the carb, and your engine WILL get rain water on it. The worst thing was the distributor getting stuck in the block due to corrosion.
    If you do it, coat the distributor body with anti-seize where it touches the block, both above and below the o-ring.

    Ditto on the set in my ways, opinionated Old Fart.  I had a Maier Racing cowl induction hood for several years, many years ago. I had kept my original hood, as the setup I had at the time - 250 6 cylinder with a Weber 2 bbl carb wouldn't fit under the stock one. Once that spun a rod bearing - I swapped it for the 351W in there now. I had a buddy paint my old hood and installed that - and never looked back. Never been a fan of fancy doohickeys on top of the stock hood. Just like the flat clean look. JMHO. 
     

    68 coupe - 351W, 4R70W, 9" 3.25 -- 65 convertible - 289 4v, C4, 8" 3.00
     

    6/02/2024 5:28 PM  #7

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,619

    Re: Shaker on a 66 mustang ?

    MS wrote:

    Different Terry, but Terry McGovern put one on his 66 fastback many years ago.  Terry has since passed and the car was sold.  It looks pretty good, but long term I think
    Leaving the outward appearance of a Classic Mustang as close to stock as possible is best. But then, I am an
    Old fart, set in my ways, and opinionated.  At least this scoop thing is something that can very easily be reversed. It is, in my opinion, at least 10,000 percent better than a Chevy cowl hood, though. Using more modern Ford stuff to modify a Mustang is way better than installing something that never belonged on any Mustang.
    From someone who has owned several 70 Mustangs with shaker scoops, be advised they are a pain in the butt to remove to adjust the carb, and your engine WILL get rain water on it. The worst thing was the distributor getting stuck in the block due to corrosion. 
    If you do it, coat the distributor body with anti-seize where it touches the block, both above and below the o-ring.

     
    Could not agree more.

    Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering, factory AC.
     

    6/03/2024 8:21 PM  #8

    Alan
    I FYI 24-7

    Offline

    From: Axtell KS
    Registered: 4/03/2013
    Posts: 515

    Re: Shaker on a 66 mustang ?

    RPM, aka Bearing Bob wrote:

    MS wrote:

    Different Terry, but Terry McGovern put one on his 66 fastback many years ago. Terry has since passed and the car was sold. It looks pretty good, but long term I think
    Leaving the outward appearance of a Classic Mustang as close to stock as possible is best. But then, I am an
    Old fart, set in my ways, and opinionated. At least this scoop thing is something that can very easily be reversed. It is, in my opinion, at least 10,000 percent better than a Chevy cowl hood, though. Using more modern Ford stuff to modify a Mustang is way better than installing something that never belonged on any Mustang.
    From someone who has owned several 70 Mustangs with shaker scoops, be advised they are a pain in the butt to remove to adjust the carb, and your engine WILL get rain water on it. The worst thing was the distributor getting stuck in the block due to corrosion.
    If you do it, coat the distributor body with anti-seize where it touches the block, both above and below the o-ring.

     
    Could not agree more.

    Coming from someone who runs a shaker hood.

    I like the interior

    Last edited by Alan (6/03/2024 8:21 PM)

    67 Coupe, 5.0 EEC IV Fuel injected. T5, 3:70 rear
     

    6/04/2024 6:39 PM  #9

    terry
    Senior 24-7 FYI Addict

    Offline

    From: vandalia, illinois
    Registered: 4/01/2013
    Posts: 1,869

    Re: Shaker on a 66 mustang ?

    Evan wrote:

    Hey there everyone. Hope y’all have been doing good. Been keeping my head down working allot on my 66 mustang and just wrapped up most of my interior re do . Just need to do new glove box door and gauges. Here’s a picture of the interior

    For now though I’m moving to the hood. A long time ago when I was younger I sold my stock hood and got a 3” cowl induction fiberglass one. It’s ok but it just doesn’t look right to me now. I just picked up a re pro steel hood for pretty cheap and I’ve been playing with the idea of doing a shaker hood scoop on it. I’ve already got the shaker set up and was looking at ordering the template to try and cut the hole with. Has anyone ever done this here? If so any pieces of advice you could give would be appreciated.

    Evan, I have a Shaker on my 65 Fastback.  Send me an email and I'll share some pics and other knowledge on installing one.  Ticir1982@gmail.com

     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Shaker on a 66 mustang ?

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.