| ||
| Visit MustangSteve's web site to view some of my work and find details for: FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events |
1 2 Jump to
Offline
Dennis wrote:
TKOPerformance wrote:
Dennis wrote:
That 75 Granada distributor says it has a steel gear. That seems odd.
It may be a "melonized" gear. Its steel, but is surface treated to work with any camshaft that isn't an 8620 billet. These gears seem to have become the standard, as rebuilders and manufacturers don't have to worry so much about application.
Yeah that could be. Would be nice if they specified.
I agree. Even the aftermarket manufacturers hardly ever spell it out. You end up having to call them or reach out to tech service via email to get the type of gear clarified. Usually a steel gear with have an S stamped into it, and you can see if its melonized by the surface texture (melonizing puts a bumpy texture on the surface kind of like it got overspray on it).
Offline
I just recurved my original distributor that has the Pertronix in it. It is in great shape and has a Ford service part number sticker on it so likely was replaced not that many miles ago. It was even clean inside. Anyway, I welded up the slots aiming for low 20's degrees mechanical advance and got 21 degrees, all in around 3000 rpms. I set total to 36 degrees and noticed the water pump spitting coolant on the balancer, so I guess I still have something to work on lol. I'll probably risk a test drive tomorrow during the daylight then pick up the pump I ordered on Monday. I went ahead and ordered a new fuel pump because I suppose it is getting ready to die and I don't need to fill the engine with gas.
Offline

Dennis wrote:
I just recurved my original distributor that has the Pertronix in it. It is in great shape and has a Ford service part number sticker on it so likely was replaced not that many miles ago. It was even clean inside. Anyway, I welded up the slots aiming for low 20's degrees mechanical advance and got 21 degrees, all in around 3000 rpms. I set total to 36 degrees and noticed the water pump spitting coolant on the balancer, so I guess I still have something to work on lol. I'll probably risk a test drive tomorrow during the daylight then pick up the pump I ordered on Monday. I went ahead and ordered a new fuel pump because I suppose it is getting ready to die and I don't need to fill the engine with gas.
Be sure and check it stops advancing around 36-42 degrees when reving above 3000RPM....
Prolly will...just a safety check.
On mine the idle was.....crisper?! Made me think 'F-1' when I snapped the throttle open real quick.
Re-adjust the air bleeds and curb idle screw . BET you'll feel the difference in it on your first test drive.
Just curious...what was the number stamped on your advance slot ?
6sally6
Offline
Yeah I checked and it quits advancing. I didn't see a number on the advance slot. It's the earlier style, not the ones with two different slots and numbers. I had to modify both weight slots, although it's probably stopping on one before the other. I test drove it and it's better, like it was with my junk distributor that had a better curve. When I switched from the junk distributor back to this original distributor, I noticed a drop off in low and mid-range power and responsiveness. It didn't pull overdrive as well. Now it's back, and it revs to my 5700 rpm shift point just fine.
Offline
1 2 Jump to
| REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on. |