FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Axle U-bolt torque

    • 1 of 1

       

    4/27/2014 6:09 PM  #1

    Nasty65
    FYI Addict

    Offline

    Registered: 4/21/2013
    Posts: 118

    Axle U-bolt torque

    Lincoln versaillies rear housing, 1/2" fine thread u-bolts, how tight to torque them?

     

    4/27/2014 8:21 PM  #2

    Daze
    Forum Moderator & Bash host 2011

    Offline

    From: Kalispell MT
    Registered: 1/24/2013
    Posts: 1,129

    Re: Axle U-bolt torque

    u-bolt is probably mild steel

    If it isn't broken...modify it anyway! http://www.DazeCars.com https://galaxieforum.boardhost.com
     

    4/27/2014 10:14 PM  #3

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,549

    Re: Axle U-bolt torque

    The shop that made mine said they were grade 8. Yep, I was suprissed too.

    Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering, factory AC.
     

    4/28/2014 11:18 AM  #4

    Daze
    Forum Moderator & Bash host 2011

    Offline

    From: Kalispell MT
    Registered: 1/24/2013
    Posts: 1,129

    Re: Axle U-bolt torque

    I just added some threads to a set of OEM u-bolts and they cut like butter. I have threaded both grade 5 and grade 8 and it cuts differently. I would think aftermarket ones would be grade 5 or 8 but I am betting OEM units are unfortunately mild steel.

    If it isn't broken...modify it anyway! http://www.DazeCars.com https://galaxieforum.boardhost.com
     

    4/28/2014 5:39 PM  #5

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,117

    Re: Axle U-bolt torque

    Torque them until you see the shock plate start to bend, then stop.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    4/29/2014 7:49 PM  #6

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,117

    Re: Axle U-bolt torque

    Are you sure they are 1/2" bolts?  Every Mustang or Versailles ubolt I have come across was 7/16" diameter.  If you torque that to same torque as a 1/2" bolt, you may have extra pieces that you cannot use.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    4/30/2014 9:33 AM  #7

    Nasty65
    FYI Addict

    Offline

    Registered: 4/21/2013
    Posts: 118

    Re: Axle U-bolt torque

    Thanks for the replys.  They are 1/2" u-bolts, not the factory ones.  I'm using the TCP spring plates I picked up on here a little while back, they look pretty stout........better not  "tighten til I see them start to bend".

       •Thread Starter
     

    4/30/2014 11:40 AM  #8

    Hornman
    Senior 24-7 FYI Addict

    Offline

    From: Mansfield, Texas
    Registered: 4/01/2013
    Posts: 1,568

    Re: Axle U-bolt torque

    I got 1/2" fine thread U bolts with my Currie large bearing rear end. Their installation instructions specifies 45 ft lb. Torquing the four nuts to 45 looked like plenty of "tight". Considering the problems Tubo had with his first set of fiberglass springs not being tight enough, tight is good.

     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Axle U-bolt torque

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.