FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Rear quarter interior panel question

    • 1 of 1

       

    6/07/2013 7:09 PM  #1

    MAW
    I FYI 24-7

    Offline

    From: Memphis, Indiana
    Registered: 4/11/2013
    Posts: 333

    Rear quarter interior panel question

    Starting to put the interior in the 66 Vert and came across a bag with 4 screws, like the one below, in it that had "rear quarter panel" written on it.



    Problem is I can only see one place where the screw goes and that is under the rear window crank



    Does anyone know where the other screw goes?

    66 Vert.  4.6 DOHC, 4R70 Auto, Heidt's M2 frontend
     

    6/07/2013 7:34 PM  #2

    josh-kebob
    Senior 24-7 FYI Addict

    Offline

    From: Madison, AL
    Registered: 4/06/2013
    Posts: 2,902

    Re: Rear quarter interior panel question

    trying to do a complete "total recall" but, is there a screw hole at either end of the bottom edge of the panel? look at the "front, bottom" edge....

    Last edited by josh-kebob (6/07/2013 7:40 PM)

     

    6/07/2013 7:42 PM  #3

    6sally6
    Hyper FYIFORD ADDICT

    Offline

    From: Surfside Beach,SC
    Registered: 4/02/2013
    Posts: 6,739

    Re: Rear quarter interior panel question

    josh-kebob wrote:

    trying to do a complete "total recall" but, is there a screw hole at either end of the bottom edge of the panel? look at the "front, bottom" edge....

    On either side of the package tray are a couple.....maybe a couple only found with seat removed.
     

    Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
     

    6/08/2013 10:12 AM  #4

    MAW
    I FYI 24-7

    Offline

    From: Memphis, Indiana
    Registered: 4/11/2013
    Posts: 333

    Re: Rear quarter interior panel question

    Thanks guys, I had those panels upholstered and they covered up the holes so wasn't sure where they went.  I didn't find anything on the front lower although it seems like one would go there. I did find one on the back top where the seat would hide it and looks like another on the back middle butt(TS) I didn't have that many screws so guess since it's not seen I can use a small screw and washer.  Thanks again, Mike

    66 Vert.  4.6 DOHC, 4R70 Auto, Heidt's M2 frontend
       •Thread Starter
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Rear quarter interior panel question

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.