FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Helping a friend with his Crate engine and Holley 4160 Carb

    • 1 of 1

       

    12/04/2015 12:55 PM  #1

    Mochaman
    Senior 24-7 FYI Addict

    Offline

    From: Royse City, Texas
    Registered: 4/02/2013
    Posts: 1,482

    Helping a friend with his Crate engine and Holley 4160 Carb

    First off, this is a 1968 cheby Camaro. He set his Holley up per Crate engine spec. 32 degrees BTCD at 3000 rpm. Says that it vacuum is 14-15.
    Says engine falters when put into drive despite a high RPM setting on his idle.

    I told him to pull plugs to see if lean or rich.

    Any Holley ideas out there. What else should he be looking at.

     

    12/04/2015 1:14 PM  #2

    whlnut
    I FYI 24-7

    Offline

    From: Brunswick, GA
    Registered: 4/02/2013
    Posts: 317

    Re: Helping a friend with his Crate engine and Holley 4160 Carb

    Most new setups need timing finalized before carb tuning. What is initial timing? May need more initial. Total should be more, usually around 36. Be sure valve adjustment is not too tight.

     

    12/04/2015 1:34 PM  #3

    hmartin025
    I FYI 24-7

    Offline

    Registered: 4/01/2013
    Posts: 365

    Re: Helping a friend with his Crate engine and Holley 4160 Carb

    Sounds like vacuum leak!
    Howard

     

    12/06/2015 9:23 AM  #4

    BobE
    Senior 24-7 FYI Addict

    Offline

    From: White Plains, NY
    Registered: 4/04/2013
    Posts: 2,558

    Re: Helping a friend with his Crate engine and Holley 4160 Carb

    As others requested, need more details ...
    What is the Idle RPM (in neutral)?
    If he is using a vacuum advance distributor, was the line plugged when checking the total timing?
    If it is a vacuum distributor, try leaving the line plugged and place into drive and see what happens.
    Monitor the vacuum when placed in 'drive'.
    Try to keep it running in drive and note the lowest RPM that can be achieved.
    Re: the Holley, what are the idle mixture screws set at?

    65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
     

    12/06/2015 11:12 AM  #5

    Pablo
    FYI Addict

    Offline

    From: Georgetown, Texas
    Registered: 4/12/2013
    Posts: 248

    Re: Helping a friend with his Crate engine and Holley 4160 Carb

    Mocha, remember, too, that the Brand X uses manifold vacuum to the distributor, not venture vacuum like the much better Ford products.
    Good luck

     

    12/06/2015 6:53 PM  #6

    Mochaman
    Senior 24-7 FYI Addict

    Offline

    From: Royse City, Texas
    Registered: 4/02/2013
    Posts: 1,482

    Re: Helping a friend with his Crate engine and Holley 4160 Carb

    I gave him some Cheby Youtube videos showing him how to set up the new Carb then gave him the link to the Holley Website that showed him how to do the initial set up..... He was an ex-officer in the USAF so you have to use small words and/or pictures with cartoon characters.
    Once he did the correct initial idle set up with the vacuum gauges he was all set. I still think he needs to do his total timing too.

       •Thread Starter
     

    12/06/2015 8:23 PM  #7

    6sally6
    Hyper FYIFORD ADDICT

    Offline

    From: Surfside Beach,SC
    Registered: 4/02/2013
    Posts: 6,739

    Re: Helping a friend with his Crate engine and Holley 4160 Carb

    Hey Ed........."write it down for him" timing FIRST carb second! geeeezzzz!!!
    Tell him its so simple a sailor could do it!

    Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Helping a friend with his Crate engine and Holley 4160 Carb

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.