FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

2/17/2018 10:31 PM  #26


Re: convertible pics

  Rosette welds and what seemed like hundreds of tack welds and the long floor pans were in July-Sept 2016

 

2/17/2018 10:48 PM  #27


Re: convertible pics

New seat riser fitted and clamped in position. I used some threaded rod in each of the seat mounting holes 
to pull riser down tight to floor pans. Marked and drill holes then rosette weld to pans and inner rocker panels.

     Thread Starter
 

2/19/2018 8:33 PM  #28


Re: convertible pics

Gonna make a little gear shift in my progress thread. Although I am still working on the passenger floor pans. I decided to take advantage of 30% off sale on sheet metal from a big vendor.
Purchased all the parts to rebuild my trunk floor. Took some careful measurements of original and 
built a assembly jig. Cut and fitted the right and left side trunk floor sides to fit rear conv brace screwed and clamp together. The finished product  in photo.

     Thread Starter
 

2/19/2018 8:42 PM  #29


Re: convertible pics

Opposite view trunk floor

     Thread Starter
 

3/06/2018 4:30 PM  #30


Re: convertible pics

Looking good to me..  Remember to eat that sheet metal elephant one leg at a time nice and steady.

 

3/07/2018 7:28 PM  #31


Re: convertible pics

Thanks Glen
Realized that old saying in the first few months.
Sometime i'll just sit on the old milk crate and think about the next bite.
Better to chew slowly than rush into a sloppy repair.
Just keep plugging away.

Never had a bad day working on Ol' Paint.

Cman

     Thread Starter
 

3/23/2018 5:48 PM  #32


Re: convertible pics

With the change to Daylight Savings Time, I think I have more time in the evening to work on 'Ol Paint,
Started cutting out trunk tin ant damage. Right side quarter panel is worth saving ( keep the original metal when possible). Will need to replace bottom few inches of outer wheel house. Will post pics later.
Fellers get out and work on your Stang.

Cman66

     Thread Starter
 

3/25/2018 5:36 PM  #33


Re: convertible pics

 Trunk front center section before cutout

     Thread Starter
 

3/25/2018 5:42 PM  #34


Re: convertible pics

 Right side before surgery

     Thread Starter
 

3/25/2018 5:47 PM  #35


Re: convertible pics

Cut out complete right side trunk floor.  Removed everything but frame rail.
Frame rail in great shape because it was galvanized. Thanks team Iacocca.
To my surprise right side quarter panel has no body filler. Amazing for a 52 year old car. 

     Thread Starter
 

3/25/2018 8:09 PM  #36


Re: convertible pics

 Frame rail cleaned of all sheetmetal

     Thread Starter
 

3/25/2018 8:13 PM  #37


Re: convertible pics

 Some surface rust on shackle bushing mount.
Will treat with rust converter and paint before installing right trunk floor

     Thread Starter
 

3/25/2018 8:19 PM  #38


Re: convertible pics

 Bottom of quarter panel before rust treatment.
Will need to replace bottom of outer wheel house complete toast. Just a few small holes in bottom of wheel opening.

     Thread Starter
 

4/02/2018 8:20 PM  #39


Re: convertible pics

Ordered and received the lower outer right side wheelhouse. Started to fit in place.
fit really well at the bottom corner of quarter panel not so good at the top.
Remember when I worked with a good bodyman years ago.
and I quote " Nothing fits right out of the box that's why we make $50.00 per hour."
Worked for about four  hours to modify the wheelhouse patch, happy with the fit.
Pictures to follow. 
Another great day working on Ol' Paint.
Cman66

     Thread Starter
 

4/09/2018 8:42 PM  #40


Re: convertible pics

Hello cmzn66. Nice Mustang! I can appreciate all the hard work!  Did you have to open a tinypic account in order to uploads these pics?

 

4/13/2018 7:12 PM  #41


Re: convertible pics

Daily driver,
I send all my pictures to my picture file in my computer.
Then I use tinypic to post.
I find it is the simplest way for me.
I don't have an account with tinypic
Cman

     Thread Starter
 

4/29/2018 1:44 PM  #42


Re: convertible pics

Nice to see the work being done properly.


Good work ain't cheap, Cheap work ain't good!   Simple Man
 

4/29/2018 4:31 PM  #43


Re: convertible pics

Rudi,
My Dad always said" if you can't find time to do it right, how are you going to find time to do it over"
Ol' Paint has been in our family since 1976. When I started the latest teardown I made myself live by
 the above quote. When its all said and done I hope to have a reliable, tight, comfortable car to enjoy.
That being said, I truly enjoy the building process. Never a bad day working on Ol' Paint.

Thanks 
Cman 66

     Thread Starter
 

5/08/2018 7:05 PM  #44


Re: convertible pics

Good update........keep up the good work and continue to post your progress.....

 

6/19/2018 1:25 AM  #45


Re: convertible pics

That looks like a fun and challenging project. Good to see great progress

 

6/20/2018 6:04 PM  #46


Re: convertible pics

Well fellas not making much progress.
Fell off into a hole, well had some repairs to make on my
travel trailer.Has consumed all my time for the last 2 months.
Need to get this repair finished have two trips to Northwest FL planned.
Those beautiful beaches are calling us.
will jump back into 'OL Paint soon.

Cman

     Thread Starter
 

7/23/2018 8:17 PM  #47


Re: convertible pics

After what seemed like forever the repairs are finished on my travel trailer.
Now I can get back to the Important repairs on Ol' Paint.
The last time I posted I had started to repair the right side outer wheel house..
Decided to take a look at the Left side wheel house, left side needs same repairs as right side.
Stripped off paint and a bunch of bondo to find that sometime in the past left quarter was repaired by 
a person addicted to plastic filler. ( 1/2" thick in two dents )
So her are some pictures All areas highlighted by marker were previous damage filled without metal work.
 

     Thread Starter
 

7/23/2018 8:51 PM  #48


Re: convertible pics

Spent about three hours slapping and picking on panel.
this is the results
sorry for the inverted photo just turn your computer or phone over.
 

     Thread Starter
 

7/24/2018 3:02 PM  #49


Re: convertible pics

nice work........

 

7/24/2018 4:14 PM  #50


Re: convertible pics

Looks good .

 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.