FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » progress update

    • 1 of 1

       

    1/06/2019 4:38 PM  #1

    1fststang
    I FYI 24-7

    Offline

    Registered: 6/02/2013
    Posts: 419

    progress update

    Been asking for advice pretty frequently the last couple weeks so I thought I would give an update.

    Ground the oil galley plugs that were interfering with the engine plate just a little so engine plate and quick time bell housing would fit flush against block.

    Rigged up my dial indicator to check bell housing alignment. That was a real pain to get the dial indicator positioned properly. I installed Lakewood dowels in the block hoping everything was in alignment.  To my satisfaction the bell housing was almost dead on well within the recommended tolerances.  Thanks QuickTime

    Installed flywheel, pilot bearing clutch pressure plate and bell housing.  Going to install the transmission after engine is in since I work alone. Would have loved installing as a combo but with the newly painted engine compartment I decided to just put the TKO 600 in afterwards

    Dropped engine in took about 15 minutes to get it on the mounts.

    Thanks everyone for the advice. Finally making a  little progress.

     

    1/06/2019 5:49 PM  #2

    Bullet Bob
    Senior 24-7 FYI Addict

    Offline

    From: Montrose, Colorado
    Registered: 4/01/2013
    Posts: 4,891

    Re: progress update

    Looks purdy darned purdy.

    BB

    "you get what you pay for, good work isn't cheap, and there are NO free lunches...PERIOD!"
     

    1/06/2019 7:16 PM  #3

    TKOPerformance
    Hyper FYIFORD ADDICT

    Offline

    From: Newark, DE
    Registered: 12/15/2014
    Posts: 7,526

    Re: progress update

    Looking good!

     

    1/06/2019 8:01 PM  #4

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,673

    Re: progress update

    Ya, looks real nice.

    Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering, factory AC.
     

    1/07/2019 1:17 PM  #5

    1fststang
    I FYI 24-7

    Offline

    Registered: 6/02/2013
    Posts: 419

    Re: progress update

    I'm hoping for the business in the front party in the back build  lol

       •Thread Starter
     

    1/07/2019 5:21 PM  #6

    whlnut
    I FYI 24-7

    Offline

    From: Brunswick, GA
    Registered: 4/02/2013
    Posts: 317

    Re: progress update

    Wow- nice work!

     

    1/07/2019 6:43 PM  #7

    6sally6
    Hyper FYIFORD ADDICT

    Offline

    From: Surfside Beach,SC
    Registered: 4/02/2013
    Posts: 6,874

    Re: progress update

    'YOU SURE GOTTA PURDY REAR END"............Kevin Spacey 2018

    I gotta agree!!
    6sal6

    Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
     

    1/07/2019 8:51 PM  #8

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,673

    Re: progress update

    6sally6 wrote:

    'YOU SURE GOTTA PURDY REAR END"............Kevin Spacey 2018

    I gotta agree!!
    6sal6

    Only from Sally! Butt I agree also.
     

    Bob. 69 Mach 1, 393W, SMOD Toploader, Armstrong  steering, factory AC.
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  progress update

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.