| ||
Visit MustangSteve's web site to view some of my work and find details for: FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events |
Offline
68P51 wrote:
Okay, going to do the arning drop. About to order the template. Any other must do's that aren't too much additional effort or $ while I'm in there? Currently stock rebuilt suspension with Granada discs and Borgeson steering. Don't want anything that will increase harshness or road noise.
Only one thing. Install a Monte Carlo Bar. Cheap and a bolt in. After that, an export brace. But mostly the Monte Carlo Bar. It will really solidify that front end so alignments can last for decades (assuming you don't do something else to the front end).
Last edited by lowercasesteve (7/30/2019 10:39 AM)
Offline
Do you have a one piece export brace?...need one
Do you have a Monte Carlo bar?.............need one
Do you have a heavy duty sway bar?.....need one
All three less than 100 bux and EZ to install. It will handle wayyyyy better than stock/brand new!
6sally6
Offline
Subframe connectors remain probably THE most important thing necessary for consistent handling. You can spring and shock the car to death trying to get better handling, but without subframe connectors all you are really doing is twisting the chassis harder.
Offline
I already have an export brace and Monte Carlo bar. The Monte Carlo bar is not on at the moment because the new A/C compressor interferes with it and is being modded. Have subframe connectors but haven't installed them yet. I was just wondering if any must do's while the spring is off.
Offline
TKOPerformance wrote:
Subframe connectors remain probably THE most important thing necessary for consistent handling. You can spring and shock the car to death trying to get better handling, but without subframe connectors all you are really doing is twisting the chassis harder.
Do you have any choice as to which ones? There are so many from which to choose.
Serious question.
Offline
Muzz 66 wrote:
TKOPerformance wrote:
Subframe connectors remain probably THE most important thing necessary for consistent handling. You can spring and shock the car to death trying to get better handling, but without subframe connectors all you are really doing is twisting the chassis harder.
Do you have any choice as to which ones? There are so many from which to choose.
Serious question.
Tin Man Fabrication makes a well designed set that is fairly easy to install (lots of welding involved).
Daze has a how-to for making your own on his website. Probably for experienced fabricators.
Last edited by Hornman (7/31/2019 8:02 PM)
Offline
Total Control also has one and their's supports an optional center suport. I did "Daze Plus" and went through the rear frame rails all the way to the front frame section since my floor was out and I also installed the TCP center support. Overkill on a coupe or fastback but should help my flimsy convertible. All the major vendors carry a variety but only the weld in connectors provide the full support potential.
Offline
I got mine from Tin Man Fabrication.........similar to what Daze has and as GPatrick noted above. These are a weld in connector. You can check these out at: tinmanfabrication.com
Offline
Hornman wrote:
Muzz 66 wrote:
TKOPerformance wrote:
Subframe connectors remain probably THE most important thing necessary for consistent handling. You can spring and shock the car to death trying to get better handling, but without subframe connectors all you are really doing is twisting the chassis harder.
Do you have any choice as to which ones? There are so many from which to choose.
Serious question.
Tin Man Fabrication makes a well designed set that is fairly easy to install (lots of welding involved).
Daze has a how-to for making your own on his website. Probably for experienced fabricators.
I run the Tin Man ones. Definitely an involved installation, but also the best ones I could find in terms of how well they tie the car together.
Offline
I have sfc's and convertible inner rockers. If I had a do over, I'd only do the conv inner rockers.
Offline
Checking out Tin Mans.
Thanks all.
REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on. |