FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » anyone running a tko 600 trans in a 69 mustang

    • 1 of 1

       

    9/02/2013 3:12 PM  #1

    GT350
    FYI Addict

    Offline

    From: scotland u.k
    Registered: 4/01/2013
    Posts: 277

    anyone running a tko 600 trans in a 69 mustang

    anyone running a tko 600 trans in a 69 mustang can give me any pointers before i go ahead and pull the trigger.

     

    9/02/2013 4:25 PM  #2

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,077

    Re: anyone running a tko 600 trans in a 69 mustang

    Not a 69, but the 69 has the same floor as my 66 I just installed one in.  There are crossmembers available that will allow you to bolt it in, but the tranny will be tilted way down.  I raised the tranny hump about 1" from stock to clear the transmission, sectioned a 67-70 floor crossmember (the piece that goes over the tranny) and built a custom lower crossmember in order to get it in there at the right angle.  The upper and lower crossmembers were positioned about 2" aft of stock location in order to not have to cantilever the tranny mount, which can cause vibration issues.

    It was a heck of alot of work to get it to fit properly.

    Search FRANKENMEMBER for my previousposts on the crossmembers.  I have lots more pics if you want to email directly.  steve@mustangsteve.com


    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    9/02/2013 4:47 PM  #3

    commish10
    FYI FORD Member

    Offline

    From: Plano, TX
    Registered: 4/02/2013
    Posts: 98

    Re: anyone running a tko 600 trans in a 69 mustang

    Installed in my 68 with 428cj. No issues other than a slight trim of the shifter hole.

     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  anyone running a tko 600 trans in a 69 mustang

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.