FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Sheared off my dip stick tube.

    • 1 of 1

       

    1/10/2020 6:00 PM  #1

    RV6
    Senior 24-7 FYI Addict

    Offline

    From: Pine Junction, CO
    Registered: 3/01/2016
    Posts: 1,250

    Sheared off my dip stick tube.

    In the never ending quest to update the 67, stuff happens. A new dip-stick tube showed up from NPD today. An easy swap, Bwahahaha! I grabbed the old one to pull it out and it came out really easy. The problem is I left the bottom part of the tube in the timing cover.
    Is there an easy way to remove the portion of tube stuck in the timing cover without pulling it. I thought I would ask before grabbing the cutting torch. 

    Gary Zilik - Pine Junction, Colorado - 67 Coupe, 289-4V, T5
     

    1/10/2020 6:15 PM  #2

    Bentworker
    I FYI 24-7

    Offline

    Registered: 9/17/2017
    Posts: 473

    Re: Sheared off my dip stick tube.

    Maybe use a tap or bolt extractor?  That would probably be able to grab onto that bit of tube.

    You would need to be careful as it would be far worse to break off a hardened High speed steel tap in there.

    Another option would be to take a center punch and grind it into the shape of a transmission bushing remover punch / chisel and try to use it- without knocking the remaining bit of tube into the block.

    Last edited by Bentworker (1/10/2020 10:09 PM)

     

    1/10/2020 6:34 PM  #3

    6sally6
    Hyper FYIFORD ADDICT

    Offline

    From: Surfside Beach,SC
    Registered: 4/02/2013
    Posts: 6,868

    Re: Sheared off my dip stick tube.

    Tap should work .
    6sal6

    Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
     

    1/10/2020 6:35 PM  #4

    josh-kebob
    Senior 24-7 FYI Addict

    Offline

    From: Madison, AL
    Registered: 4/06/2013
    Posts: 2,902

    Re: Sheared off my dip stick tube.

    Gary, if you have room to work, see if you can bend a section of whats left of the tube, just enough to grab that bent section with a pair needle nose pliers. If you can grab it with those pliers, you may be able to twist it more and pull it out.

     

    1/10/2020 6:59 PM  #5

    HudginJ3
    Senior 24-7 FYI Addict

    Offline

    From: Cedar Hill, TX
    Registered: 4/29/2015
    Posts: 1,249

    Re: Sheared off my dip stick tube.

    I would first recommend the tap method. It looks like a flange might be left to be able to grab it with some dikes to pry it out. If you smash it too much with the dikes you can run a small diameter punch between the hole and the piece to collapse it and then pull it out. But again the best bet is the tap. 

    70, ragtop 351W/416 stroker Edel Performer heads w pro flow 4, Comp roller 35-421-8. T5
     

    1/10/2020 7:21 PM  #6

    lowercasesteve
    Senior 24-7 FYI Addict

    Online!

    From: Auburn, Ca
    Registered: 4/01/2013
    Posts: 1,255

    Re: Sheared off my dip stick tube.

    Try an easy out.  It worked for me when I did the same.

    Original owner - 351w,T-5, 4whl disks, power R&P
     

    1/11/2020 11:33 AM  #7

    Rudi
    Senior 24-7 FYI Addict

    Offline

    From: Stuck in the 50's Welland Ca
    Registered: 4/01/2013
    Posts: 3,976

    Re: Sheared off my dip stick tube.

    I see from your VMF post you have a slide hammer. Get a long socket head cap screw, one that  the head will pass into the tube in the timing cover, push the head down into the hole so that the head will snag the bottom of the tube.
    You should be able to attach the threaded end of the cap screw to the slide hammer and then bump the busted  part of the tube out.
    Of course the whole set up should be assembled before you put the slide hammer down there, you don’t want to drop a loose  cap screw down into the pan.

    Good work ain't cheap, Cheap work ain't good!   Simple Man
     

    1/11/2020 11:45 AM  #8

    RV6
    Senior 24-7 FYI Addict

    Offline

    From: Pine Junction, CO
    Registered: 3/01/2016
    Posts: 1,250

    Re: Sheared off my dip stick tube.

    Rudi wrote:

    I see from your VMF post you have a slide hammer. Get a long socket head cap screw, one that the head will pass into the tube in the timing cover, push the head down into the hole so that the head will snag the bottom of the tube.
    You should be able to attach the threaded end of the cap screw to the slide hammer and then bump the busted part of the tube out.
    Of course the whole set up should be assembled before you put the slide hammer down there, you don’t want to drop a loose cap screw down into the pan.

    Rudi,

    Wonderful idea. It is now on my list of things to try. That little tube is really stuck. Sorta makes me wonder how I'll get the new one installed.

    Gary Zilik - Pine Junction, Colorado - 67 Coupe, 289-4V, T5
       •Thread Starter
     

    1/11/2020 1:09 PM  #9

    RV6
    Senior 24-7 FYI Addict

    Offline

    From: Pine Junction, CO
    Registered: 3/01/2016
    Posts: 1,250

    Re: Sheared off my dip stick tube.

    Well, I tried a tap and broke it off in the tube and managed to get it out. I tried and ez-out with heat, nothing. I tried Rudi's suggestion of a cap screw the catch the bottom of the tube and try and ease it out with a slide hammer. Nothing. It just peeled off slivers of the tube till there was nothing to crab. I tried a punch to start collapsing the tube so I  could get an all in there and collapse the rest. I'm afraid of breaking the casting with the last method so I am going to pull the timing chain cover. 
    I think the fact that the tube has been in the cover for 55 years has something to do with its refusal to depart the cover. At least the front of the engine will be sparkly again.

    Gary Zilik - Pine Junction, Colorado - 67 Coupe, 289-4V, T5
       •Thread Starter
     

    1/11/2020 1:15 PM  #10

    RV6
    Senior 24-7 FYI Addict

    Offline

    From: Pine Junction, CO
    Registered: 3/01/2016
    Posts: 1,250

    Re: Sheared off my dip stick tube.

    I really though Rudi's idea was going to work. I had to shave down the head of the cap screw a little to get it to fit.

     

    Gary Zilik - Pine Junction, Colorado - 67 Coupe, 289-4V, T5
       •Thread Starter
     

    1/18/2020 4:56 PM  #11

    RV6
    Senior 24-7 FYI Addict

    Offline

    From: Pine Junction, CO
    Registered: 3/01/2016
    Posts: 1,250

    Re: Sheared off my dip stick tube.

    After pulling the front of the engine off to replace a dip stick tube all is back together again. What a pain in the butt. Butt, I do have a new water pump and timing chain in the process. 

    Gary Zilik - Pine Junction, Colorado - 67 Coupe, 289-4V, T5
       •Thread Starter
     

    1/18/2020 5:45 PM  #12

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,283

    Re: Sheared off my dip stick tube.

    Have you considered a little clearancing of that idler pulley bracket under the thermostat.  Man, those tstat housing bolts are a PITA even without building a wall in front!

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    1/18/2020 6:03 PM  #13

    josh-kebob
    Senior 24-7 FYI Addict

    Offline

    From: Madison, AL
    Registered: 4/06/2013
    Posts: 2,902

    Re: Sheared off my dip stick tube.

    Looks good Gary...

     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Sheared off my dip stick tube.

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.