FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Drum hub question

    • 1 of 1

       

    9/22/2013 8:42 PM  #1

    True74yamaha
    Senior 24-7 FYI Addict

    Offline

    From: Salt Lake City
    Registered: 5/07/2013
    Posts: 2,537

    Drum hub question

    I was curious my cousin wants to do mustang steve cobra set up. But as she is restoring her car was stripped of the spindles. I have now sourced the spindles minus the hubs which I need the car has 70 big bearing spindles. I'm having a hard time sourcing big bearing hubs. Will a early pre 70 hub fit?  I know the a12 outer bearing has the same height and od measurements as the a2.  But the a13 bearing is wear the problem lies will an a13 fit it has same od measurments as the a6 but the height is different slightly. So will a early hub fit a late spindle?

     

    9/22/2013 9:32 PM  #2

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,797

    Re: Drum hub question

    Hubs are same 65-73.  The later bearings just have a larger hole in the center.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    9/22/2013 9:41 PM  #3

    True74yamaha
    Senior 24-7 FYI Addict

    Offline

    From: Salt Lake City
    Registered: 5/07/2013
    Posts: 2,537

    Re: Drum hub question

    Awesome thanks Steve! I kinda figured they were plus seance you say you can use 65-73 drum hubs with your mii conversions I figured they had to be the same. Thank you again

       •Thread Starter
     

    9/23/2013 10:59 AM  #4

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,995

    Re: Drum hub question

    So does anyone have the bearing part numbers for the larger 70 spindle? The knucklehead at the parts store couldn't find it about a year ago when I was looking. Ended up using a 69 spindle. Thanks.

    Bob

    Bob. 21.5 freeway MPG 69 Mach 1, 5.0 GT40P heads, SMOD Toploader, Armstrong  steering, factory AC
     

    9/23/2013 12:20 PM  #5

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,797

    Re: Drum hub question

    I believe A12 and A13 fit the 70 -newer spindles.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    9/23/2013 1:00 PM  #6

    rpm
    Senior 24-7 FYI Addict

    Offline

    From: Bakersfield, Ca
    Registered: 9/17/2013
    Posts: 3,995

    Re: Drum hub question

    Thanks Steve, I saw those numbers listed but didn't think they were the complete numbers.

    Bob

    Bob. 21.5 freeway MPG 69 Mach 1, 5.0 GT40P heads, SMOD Toploader, Armstrong  steering, factory AC
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Drum hub question

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.