FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

11/15/2026 8:13 PM  #1


Modifying a 68 shifter to work with a 4R70W - anyone?

  So my next winter project will be modifying a 1968 shifter to be able to properly shift the 4R70W transmission in my 68. When I first installed the 4R70W I was going to use the 1994 shifter and cable to shift with, and I was going to use the bezel from my 68 shifter, but I couldn’t get it to fit properly. I simply installed a boot around the shift handle and have driven it that way.
 I would like to figure out how I can modify the shifter detents to match the detents in the transmission. I have included pictures of the current installation, and what the 1994 shifter detents look like.
If anyone had done this project before, and got the 68 shifter to work with the cable installation, please jump in here and give me some direction. The current installation on the transmission has a lever that points downward. I really don’t want to tear into the trans and swap out the shift shaft and lever. The system installed now works fine. I just want to see if I can get the 68 shifter to work with the transmission as is.


68 coupe - 351W, 4R70W, 9" 3.25 -- 65 convertible - 289 4v, C4, 8" 3.00
 

11/15/2026 8:17 PM  #2


Re: Modifying a 68 shifter to work with a 4R70W - anyone?


68 coupe - 351W, 4R70W, 9" 3.25 -- 65 convertible - 289 4v, C4, 8" 3.00
     •Thread Starter
 

11/15/2026 8:19 PM  #3


Re: Modifying a 68 shifter to work with a 4R70W - anyone?


68 coupe - 351W, 4R70W, 9" 3.25 -- 65 convertible - 289 4v, C4, 8" 3.00
     •Thread Starter
 

Yesterday 6:44 AM  #4


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

I'd try altering that angle bracket that comes off the bottom of the shifter, making it longer or shorter so that the detents match.  If that's not feasible, there's probably one on the transmission that you can alter.  You have to determine how much travel the transmission lever has between detents where the cable attaches, then match that to the point where the cable attaches to the lever on your shifter.


Founding Member of the Perpetually Bewildered Society
 

Yesterday 8:16 AM  #5


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

This Lokar unit allows you to change the angle of attach and the throw to match various shifters.  One could measure and make something similar but sometimes a piece that works is easier and cheaper in the long run. 

I used the column shift version with this shaft on a 46 Ford project with a GM column.  The detents all line up.


 Lokar
 

 

Yesterday 8:20 AM  #6


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

I’m not familiar with either of these shifter’s mechanisms, but could the 94 shifter be made to fit the 68 shifter’s base plate?


65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
 

Yesterday 12:24 PM  #7


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

I swear I thought I've read where someone has done this.  I'll search later after work.

 

Yesterday 12:48 PM  #8


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

I think I remember Bullet Bob having done this mod.


Bob. 21.5 freeway MPG 69 Mach 1, 5.0 GT40P heads, SMOD Toploader, Armstrong  steering, factory AC
 

Yesterday 3:41 PM  #9


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

It boils down to having the cable attach to the lever under the shifter and on the transmission at the same distance from the center of the respective shaft that they pivot on - as long as the transmission shift gates follow the PRND2L standard - least in my experience.  I've never done a 4-speed automaic but I've adapted newer C4's with the longer levers to OE shifters.

Last edited by John Ha (Yesterday 3:51 PM)


Founding Member of the Perpetually Bewildered Society
 

Yesterday 6:47 PM  #10


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

Ron, you could try asking MS if he still has the pics from this post.
https://fyi.boardhost.com/viewtopic.php?id=7337
One of the critical parts is the witness mark he describes.
I used a 95 cable on my 65 convertible, it shifted well, but I was not happy with the 5' cable looped above the convertible under floor brace, it was too close to the driveshaft and the loop was too tight a radius.
I chose to make a bell crank operated by rods, so i didn't have to move the lever and DTR. 
I know that Bullet Bob did the same once I mentioned it to him. I'm sure that his rods are a lot better than my attempt. I'm not real happy with mine, which is why I eventually will try a custom made cable.
I know he had to modify his detents, I, like Steve, didn't have to. I suspect the difference is the green dot shifter bucket. 

With my shattered foot, I'm still not able to get to the shed and take any pics for you. 
I know that Bullet's daughter and son-in-law Renee and Shawn, have moved to Montrose CO, to be with Jean. He's a nice guy, and would probably snap some pics of Bullets bell crank.

Last edited by 50vert (Yesterday 6:52 PM)


"Those telephone poles were like a picket fence"
 

Yesterday 6:50 PM  #11


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

John Ha wrote:

I'd try altering that angle bracket that comes off the bottom of the shifter, making it longer or shorter so that the detents match.  If that's not feasible, there's probably one on the transmission that you can alter.  You have to determine how much travel the transmission lever has between detents where the cable attaches, then match that to the point where the cable attaches to the lever on your shifter.

I do have some wiggle room where the cable attaches to the transmission (click on link for photo)

https://ibb.co/nkNWsT5
 


68 coupe - 351W, 4R70W, 9" 3.25 -- 65 convertible - 289 4v, C4, 8" 3.00
     •Thread Starter
 

Yesterday 6:58 PM  #12


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

50vert wrote:

Ron, you could try asking MS if he still has the pics from this post.
https://fyi.boardhost.com/viewtopic.php?id=7337
One of the critical parts is the witness mark he describes.
I used a 95 cable on my 65 convertible, it shifted well, but I was not happy with the 5' cable looped above the convertible under floor brace, it was too close to the driveshaft and the loop was too tight a radius.
I chose to make a bell crank operated by rods, so i didn't have to move the lever and DTR. 
I know that Bullet Bob did the same once I mentioned it to him. I'm sure that his rods are a lot better than my attempt. I'm not real happy with mine, which is why I eventually will try a custom made cable.

With my shattered foot, I'm still not able to get to the shed and take any pics for you. 
I know that Bullet's daughter and son-in-law Renee and Shawn, have moved to Montrose CO, to be with Jean. He's a nice guy, and would probably snap some pics of Bullets bell crank.

Thanks Barry, but my cable installation (see photo) is well out of the way of anything, and it currently works well. I will try to install the 68 shifter and set the shifter detent in Park and adjust the rod end at the transmission so that the arm is also in Park, and see where it goes from there. The installed shifter and the 68 shifter are very similar in size and actuation direction, so I will see were we sit when I get it installed. "Where there's a will, there's a way...."
 


68 coupe - 351W, 4R70W, 9" 3.25 -- 65 convertible - 289 4v, C4, 8" 3.00
     •Thread Starter
 

Yesterday 7:02 PM  #13


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

GPatrick wrote:

This Lokar unit allows you to change the angle of attach and the throw to match various shifters.  One could measure and make something similar but sometimes a piece that works is easier and cheaper in the long run. 

I used the column shift version with this shaft on a 46 Ford project with a GM column.  The detents all line up.

I looked at that, but I really don't want to have to drop the pan and remove the valve body to swap out the shift shaft if I can get it to work some other way. Thanks for the suggestion. 


 Lokar
 

 


68 coupe - 351W, 4R70W, 9" 3.25 -- 65 convertible - 289 4v, C4, 8" 3.00
     •Thread Starter
 

Yesterday 7:04 PM  #14


Re: Modifying a 68 shifter to work with a 4R70W - anyone?

I used a part from a Windsor- Fox setup, witch is just a piece of RHS that slides over the lever, with stud welded to it and a grub screw on the side for adjustment. the correct position is close to .25" lower than the original hole.


"Those telephone poles were like a picket fence"
 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.