FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » Mounted Flaming River tilt column

    • 1 of 1

       

    11/17/2024 6:04 PM  #1

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,553

    Mounted Flaming River tilt column

    Today I got the FR column mounted.  The dash bracket they sell is to wide so I had to add a pretty good size bevel so it would sit flat against the underside of the dash where it clamps the column.  Thir bracket they sell came with long bolts and lock nuts.   The bolts are the same thread as the inserts in the clutch pedal bracket where the stock column bracket bolts to.  I just removed the studs ford used and other than the bevels I added, it bolts up.  Somewhat challenging to get it all to line up and start a bolt while holding it and trying to get the bolt started in the insert which slides around.  The bracket does not slide to easy on the column but it's designed that way so once it is clamp, it's not moving!  Had to put the gauges in just for the picture.




     

    11/18/2024 8:05 AM  #2

    BobE
    Senior 24-7 FYI Addict

    Offline

    From: White Plains, NY
    Registered: 4/04/2013
    Posts: 2,525

    Re: Mounted Flaming River tilt column

    Great to see these pictures, looks good, continued good 'build' going forward. 

    65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
     

    11/18/2024 9:30 AM  #3

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,553

    Re: Mounted Flaming River tilt column

    BobE wrote:

    Great to see these pictures, looks good, continued good 'build' going forward. 

     
    Thank you

       •Thread Starter
     

    11/18/2024 10:15 AM  #4

    KeithP
    I FYI 24-7

    Offline

    From: Scottsdale, AZ
    Registered: 6/10/2013
    Posts: 372

    Re: Mounted Flaming River tilt column

    I have one of those with EPAS. After you install your steering wheel could you post a picture of the full up tilt position. Mine does not tilt up as much as I would like. It tilts down a lot more than up.

    1966, vert, 347 stroker, T5z, 4 wheel disc, pb, 3.70 LS 9", EPAS
     

    11/18/2024 1:30 PM  #5

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,553

    Re: Mounted Flaming River tilt column

    KeithP wrote:

    I have one of those with EPAS. After you install your steering wheel could you post a picture of the full up tilt position. Mine does not tilt up as much as I would like. It tilts down a lot more than up.

     
    It might be a month before I get to that part but I need to order one so I can set the column where it needs to be.

       •Thread Starter
     

    11/18/2024 2:20 PM  #6

    KeithP
    I FYI 24-7

    Offline

    From: Scottsdale, AZ
    Registered: 6/10/2013
    Posts: 372

    Re: Mounted Flaming River tilt column

    RTM wrote:

    KeithP wrote:

    I have one of those with EPAS. After you install your steering wheel could you post a picture of the full up tilt position. Mine does not tilt up as much as I would like. It tilts down a lot more than up.

     
    It might be a month before I get to that part but I need to order one so I can set the column where it needs to be.

    With the new steering wheel/seats/Malwood hydraulic clutch pedal I have I moved the column up. That ribbon cable coming out of the side of the column is now on the front side of that aluminum column clamp. Don't buy the steering shaft to steering box joint until you determine where you want the column positioned.
     

    1966, vert, 347 stroker, T5z, 4 wheel disc, pb, 3.70 LS 9", EPAS
     

    11/19/2024 7:53 AM  #7

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,553

    Re: Mounted Flaming River tilt column

    KeithP wrote:

    RTM wrote:

    KeithP wrote:

    I have one of those with EPAS. After you install your steering wheel could you post a picture of the full up tilt position. Mine does not tilt up as much as I would like. It tilts down a lot more than up.

     
    It might be a month before I get to that part but I need to order one so I can set the column where it needs to be.

    With the new steering wheel/seats/Malwood hydraulic clutch pedal I have I moved the column up. That ribbon cable coming out of the side of the column is now on the front side of that aluminum column clamp. Don't buy the steering shaft to steering box joint until you determine where you want the column positioned.
     

     
    I have a D shaft and knuckles that haven't been fitted yet.  But I do have a question.  I was told not to slip the D shaft inside of the flaming River column shaft.   I think that's the best way to mount it and install a roll pin once I establish the final position. In my mind I have a point where it can collapse.  Can't recall why my buddy said not to mount it that way and I'm pretty sure he had read that somewhere online.

       •Thread Starter
     

    11/19/2024 8:53 AM  #8

    KeithP
    I FYI 24-7

    Offline

    From: Scottsdale, AZ
    Registered: 6/10/2013
    Posts: 372

    Re: Mounted Flaming River tilt column

    RTM wrote:

    KeithP wrote:

    RTM wrote:

     
    It might be a month before I get to that part but I need to order one so I can set the column where it needs to be.

    With the new steering wheel/seats/Malwood hydraulic clutch pedal I have I moved the column up. That ribbon cable coming out of the side of the column is now on the front side of that aluminum column clamp. Don't buy the steering shaft to steering box joint until you determine where you want the column positioned.
     

     
    I have a D shaft and knuckles that haven't been fitted yet. But I do have a question. I was told not to slip the D shaft inside of the flaming River column shaft. I think that's the best way to mount it and install a roll pin once I establish the final position. In my mind I have a point where it can collapse. Can't recall why my buddy said not to mount it that way and I'm pretty sure he had read that somewhere online.

    I don't think the D shaft can be moved inside the column(mine is not collapsible). Maybe because mine has their EPAS attached? I just moved the whole column forward. When I moved the whole column forward I had to source a longer joint.
     

    1966, vert, 347 stroker, T5z, 4 wheel disc, pb, 3.70 LS 9", EPAS
     

    11/19/2024 9:38 AM  #9

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,553

    Re: Mounted Flaming River tilt column

    KeithP wrote:

    RTM wrote:

    KeithP wrote:


    With the new steering wheel/seats/Malwood hydraulic clutch pedal I have I moved the column up. That ribbon cable coming out of the side of the column is now on the front side of that aluminum column clamp. Don't buy the steering shaft to steering box joint until you determine where you want the column positioned.
     

     
    I have a D shaft and knuckles that haven't been fitted yet. But I do have a question. I was told not to slip the D shaft inside of the flaming River column shaft. I think that's the best way to mount it and install a roll pin once I establish the final position. In my mind I have a point where it can collapse. Can't recall why my buddy said not to mount it that way and I'm pretty sure he had read that somewhere online.

    I don't think the D shaft can be moved inside the column(mine is not collapsible). Maybe because mine has their EPAS attached? I just moved the whole column forward. When I moved the whole column forward I had to source a longer joint.
     

     
    The original D shaft that came with the R&C MII kit slips inside of the FR column nicely.  The column itself is not the collapsible column FR sells.  I was thinking that with the D shaft slide into the FR column and held by a roll pin that it wouldn't be a solid connection, the roll pin could shear.    I'm sure I'm over thinking this.   I'll research how FR suggest I connect the D shaft to the column.

       •Thread Starter
     

    11/19/2024 4:26 PM  #10

    Nos681
    Senior 24-7 FYI Addict

    Offline

    From: Atlantic Mine, Michigan
    Registered: 7/14/2016
    Posts: 3,292

    Re: Mounted Flaming River tilt column

    If you shear a roll pin on a D shaft connection, you might be in the hospital.

    Last edited by Nos681 (11/19/2024 4:27 PM)

     

    Yesterday 7:22 AM  #11

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,553

    Re: Mounted Flaming River tilt column

    Nos681 wrote:

    If you shear a roll pin on a D shaft connection, you might be in the hospital.

     
    I'm sure of it, again just may be over thinking things like I always do.

       •Thread Starter
     

    Yesterday 8:21 AM  #12

    BobE
    Senior 24-7 FYI Addict

    Offline

    From: White Plains, NY
    Registered: 4/04/2013
    Posts: 2,525

    Re: Mounted Flaming River tilt column

    RTM - I'm not sure how one could shear a roll pin on this D-shaft arrangement.  I doubt that would occur due to a twisting motion.  
    BTW - my 12-year-old R&C MII D-Shaft joints use setscrews.  Have they changed to using roll-pins? 

    65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
     

    Yesterday 5:37 PM  #13

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,553

    Re: Mounted Flaming River tilt column

    BobE wrote:

    RTM - I'm not sure how one could shear a roll pin on this D-shaft arrangement.  I doubt that would occur due to a twisting motion.  
    BTW - my 12-year-old R&C MII D-Shaft joints use setscrews.  Have they changed to using roll-pins? 

     
    Talking about two different things.  I'll post a picture of what I'm referring to.

       •Thread Starter
     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  Mounted Flaming River tilt column

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.