| ||
| Visit MustangSteve's web site to view some of my work and find details for: FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events |
Offline
I recurved my distributor, and while setting the timing I noticed coolant splashing onto the balancer. No big deal, it's been over 20 years since I put a water pump on it. I had to order a water pump because nobody around here stocks one. I got it Monday, put it on, and it leaked residual coolant from the engine before I even put coolant in. I pulled the pump off today and found that the gasket between the plate and the pump was actually the one that goes between the timing cover and the pump, so it doesn't properly seal around the two plate attaching bolts on the bottom. I got lucky and the parts store stocked a second pump when they got mine, so I got the gaskets from that one. I put it back together, making sure everything was proper. No leaks. I took it for a drive, and it runs really well now with the new curve. It pulled strong all the way to 6k for the first time and unfortunately wheel hopped pretty good in second gear so I let off. I pulled into my garage and it is steaming badly. It's squirting coolant out of the bottom of the water pump right onto the balancer. I would say it had a bad gasket but I was really careful with them and it didn't leak initially. Now I'm wondering if there is a hole in the front cover or something. I can't really see exactly where it is coming from.
I guess I'll pull it apart again tomorrow, but hoping someone has seen something similar before.
Offline

Typical Mustang repair. Surprised you didn't snap off a bolt or sumpin.
Offline
Thinking through it, I think it has to be a gasket leaking at the port in the block, putting coolant on the back side of the pump and then it's coming out the weep hole at the bottom of the pump. I also think this was the original leak, so not really pump problem. I'm going to buy a new front cover. This really is kind of a dumb design when you compare it to a Chevy timing cover setup.
Of course, I noticed my fuel gauge doesn't work after replacing the speedo cable that was leaking. Did I mention needing a match lol?
Offline

The weep hole on the pump is on the front side of the shaft seal and should not leak unless the seal is defective.
If it was steaming badly from this location, I would think the engine had overheated after the strong pulls that were made, over pressurized the system. I wouldn’t think that should force water out the weep hole in the pump.
What pressure radiator cap are you using?
As there are several different pump types used though the years, what year engine/pump is this?
And, don't get a match yet!
Offline
Dennis wrote:
Thinking through it, I think it has to be a gasket leaking at the port in the block, putting coolant on the back side of the pump and then it's coming out the weep hole at the bottom of the pump. I also think this was the original leak, so not really pump problem. I'm going to buy a new front cover. This really is kind of a dumb design when you compare it to a Chevy timing cover setup.
Of course, I noticed my fuel gauge doesn't work after replacing the speedo cable that was leaking. Did I mention needing a match lol?
Sometimes the timing cover can get pin holes in it that are hard to see, but leak. Replacing the cover is a good idea if its already that far apart, but I agree with BobE that if its legit leaking out the weep hole in the pump the shaft seal in the pump is bad. That's the only way coolant gets to that hole.
As far as the Chevy setup being better, IMO it has its own issues; its just different. One thing I never liked about the SBC was that prior to going to a roller cam there was no positive cam retention, and the timing cover was just stamped steel. This made running a roller cam in a non roller block a PITA because you had to address cam walk. You had to run a cam button and either a cast front cover, or some other system (I made a plate bolted to the back of the water pump once that had a stop bolt that prevented the cover from flexing) to stop cam walk.
There's also that stupid fuel pump pushrod and plate deal for a mechanical fuel pump, whereas the Ford pump just bolts to the cover and rides directly on the cam eccentric.
I'll give you that the water pump bolting directly to the block is a better setup from a sealing standpoint.
Offline
Is it running hot?
Offline

The covers are subject to getting pinhole leaks within the water passages
Timing covers on ebay are about $40 to $60 and most are really good quality and use the crank seal that is installed from the front, a great improvement. I have installed one on just about every small block I have built.
I always add sealer and check the gasket fit on the rear plate and make sure the two bolts are tight.
WYAIT, add a Fel-Pro repair sleeve to your balancer to avoid future seal leaks
Offline

Offline
Offline
I'm thinking the gasket is leaking at the upper main water passages, and is going behind the pump and out the hole I circled in red. This appears to be exactly the spot it's coming out. I ordered a new cover and dipstick tube. It could be there is a pinhole leak I didn't see, but considering the amount leaking out the last time I drove it, whatever it is got suddenly worse. Hopefully it will all be behind me with the new parts. The car doesn't run hot according to the gauge and doesn't have any overheating sysmptoms. The good news is I got my fuel gauge working again. ![]()

Last edited by Dennis (Yesterday 1:01 PM)
Offline
This is interesting. I've never, ever put sealant or adhesive on the gasket between the pump and the plate. I guess this time I'll use some weatherstrip adhesive. The gasket wasn't the greatest quality and I've got FelPro on order. I suppose I'll just put the new front cover on also as the cover gasket is weeping anyway. I suspect the difference in impellers and suspect the new pump is creating too much pressure. Now what to do...
Editing - can't get the pics to load properly
Last edited by Dennis (Yesterday 3:42 PM)
Offline
I give up on pics for now. The gasket blew out between the bottom two plate bolts, and the new pump impeller is 3-5/8" with 8 blades whereas the old one is 4" with 6 blades.
Offline
The Gates gaskets are mushy and disintegrate as I'm removing them. They are not like the pump to cover Fel-Pro gasket I used on the previous install. I could reuse that gasket. I'm going to chalk this one up to junk gaskets and install the new front cover with FelPro gaskets. I will use some weatherstrip adhesive on the plate to pump gasket even though in almost 50 years of replacing water pumps I never have.
Offline
I skin all these gaskets with RTV. It never hurts.
Offline

TKOPerformance wrote:
I skin all these gaskets with RTV. It never hurts.
Ditto that. (pretty much for all gasketed surfaces and have been doing that for at least 50 years)
| REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on. |