FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » Swap Meet
  •  » 1966 Bronco

    • 1 of 1

       

    7/14/2014 8:15 PM  #1

    Ray
    Active Member

    Offline

    Registered: 7/14/2014
    Posts: 6

    1966 Bronco

    Good Shape for restoring. Has original 170 CU IN motor. 3 speed transmission . Also comes with rebuilt 302 motor with C4 transmission. With tail shaft and adapter to mate with transfer case . Has 6 in lift kit , fender flares, new shocks, high energy body mounts, rear fender wells which have NOT been cut out.
    $4500.00 Call Ray at 903- 714-9897

     

    7/15/2014 5:52 AM  #2

    tweet66
    FYI FORD Member

    Offline

    From: Pennsauken, NJ
    Registered: 4/01/2013
    Posts: 60

    Re: 1966 Bronco

    Any pix? Where are you located?

     

    7/15/2014 3:54 PM  #3

    Ray
    Active Member

    Offline

    Registered: 7/14/2014
    Posts: 6

    Re: 1966 Bronco

       •Thread Starter
     

    7/15/2014 7:08 PM  #4

    tweet66
    FYI FORD Member

    Offline

    From: Pennsauken, NJ
    Registered: 4/01/2013
    Posts: 60

    Re: 1966 Bronco

    That's not a bad looking truck at all. How much/many rust issues and where? Does it run currently? Where are you located?
    Thanks
    Ken

     

    7/16/2014 9:59 PM  #5

    Ray
    Active Member

    Offline

    Registered: 7/14/2014
    Posts: 6

    Re: 1966 Bronco

    Ken,
    There is a small amount of rusting on the front edge of the hood. The floors were rusted out but have been replaced with 1/8 in diamond plate. No, it does not run but comes with 2 motors. One motor is the original , a 6 cylinder.
    Also included is the V8 302 that has been rebuilt that runs but has never been installed. We are in east Texas.
    Thanks,
    Ray

       •Thread Starter
     

    8/08/2014 9:38 PM  #6

    cougrnut
    FYI Addict

    Offline

    From: hershey
    Registered: 4/03/2013
    Posts: 194

    Re: 1966 Bronco

    do you have any power steering parts?  Am in dire need for a early bronco power steering boc for brother's 67.

     

    8/10/2014 7:39 AM  #7

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,189

    Re: 1966 Bronco

    The patina on that paint is perfect!

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    8/10/2014 8:09 AM  #8

    Don
    Senior 24-7 FYI Addict

    Offline

    From: Coppell, Texas
    Registered: 4/02/2013
    Posts: 1,221

    Re: 1966 Bronco

    MustangSteve wrote:

    The patina on that paint is perfect!

    GAS MONKEY special,, spray a coat of clear on it 

     

     

    1 of 1

  • Index
  •  » Swap Meet
  •  »  1966 Bronco

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.