FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

6/01/2013 2:20 PM  #1


cobra powered by FORD Black/silver valve cover leak at oil cap 289/fb

My drivers side valve cover leaks oil from the valve cover oil cap( i have the oil cap with 2 prongs and a gasket basically push and twist, i was thinking of going to the Rubber grommet on the valve cover and installing the same type cap only with the push into the grommet type oil cap
Anyone else done this,and does anyone know the part #

I looked at Rudi's Immaculate mustang last night at our local cruise show but forgot to ask him Questions on the valve cover Grommet if his valve covers had the notches for the cap with the 2 ears or not?

I ran a dye thru the engine and this is definitely where the oil is coming from.

Jimmy O 

Last edited by Fastbackbhoy (6/01/2013 2:42 PM)

 

6/01/2013 3:34 PM  #2


Re: cobra powered by FORD Black/silver valve cover leak at oil cap 289/fb

jimmy, my engines (289 and 302) both blew oil out different places like that.  It started at the oil fill cap and I replaced it with one that sealed better.  Then it started blowing it out the dipstick.  I went to a vented oil fill cap that had the vent holes on the bottom but eventually it filled up with oil and started blowing oil out the vent holes.  I then went to a fill cap that had a single vent hole and put a peice of tubing on it, this tubing then connects to my air breather.  I got this idea from MS he used a barbed fitting to attech his to the breather.
I can take some pic and post if needed.  I checked everything under the sun to correct this problem but nothing cured it.  My Pcv valve works fine and its hooked to the carb base from the right valve cover and the oil fill is on the left cover
not sure this is your problem but its something to check!!

 

6/01/2013 3:39 PM  #3


Re: cobra powered by FORD Black/silver valve cover leak at oil cap 289/fb

Nice talking with you last night at the cruise Jimmy and glad to to see you enjoying your very pretty fastback. I like the colour and the nice job on the paintwork.
The part you need is available from CJ Pony, part # 6892F around 6 bucks which includes the grommet to convert the "twist in" to "push in" and the PCV grommet for the other side..
If I remember correctly I also used RTV when I installed that grommet on my engine.
, just a bit more insurance on a good seal.
Make sure you order a push "in" breather rather than the push "on" version, they have both.

Last edited by Rudi (6/01/2013 3:41 PM)


Good work ain't cheap, Cheap work ain't good!   Simple Man
 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.