FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

11/27/2017 8:45 AM  #1


E-brake cable install with MS Cobra rear brakes?

I recently installed the MS Cobra rear brake conversion and now looking to complete the emergency brake installation.
Has anyone completed and documented a similar install on a 65-66 car?
I reviewed the brake cable install posted by jkordzi, which looks very nice using the later brakes and cables, but I am looking specifically for the cobra install using the 2000 cables recommended by MS.
Any pointers are appreciated.
 

 

11/27/2017 11:46 AM  #2


Re: E-brake cable install with MS Cobra rear brakes?

This will be my next project, so I’m interested in the responses.

 

11/27/2017 9:09 PM  #3


Re: E-brake cable install with MS Cobra rear brakes?

I have some info on this.

Cut the new cable housings to fit between the calipers and the brackets in the drive tunnel, routing above the mufflers and using the original clamps to hold them up under the rear seat area.

Overlap the new cable wire with the original front cable about 6” and apply two 1/8” cable clamps. Tractor Supply has stainless clamps for about $1.99.

If you have a 65, it is better to replace the two front cables and their front spreader bar with the 66 front horseshoe and a single long cable.

If you don’t like the overlap/clamp system, you can build a single wire cable that goes from one caliper to the front, through the hoseshoe and back to the other caliper.

Adjust tension so it is “just tight” when the underdash handle is at rest and the caliper levers are at rest. The brakes will be applied as soon as the caliper levers start to move, so be sure they are at rest with the ebrake not applied.


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 

11/28/2017 9:41 AM  #4


Re: E-brake cable install with MS Cobra rear brakes?

I do like the idea of a single cable and use of the 66-style front connector. I'd be interested in opinions on the best way to cut the new housing and still retain the housing ends so that the housing will mount correctly at the caliper and tunnel mount points. Maybe cut the housing halfway between the two ends and reconnect with an outer metal tube, or cut the ferrule on one end and then re-crimp to attach to the shortened housing? Then build a completely new cable that has a new swedge end at each caliper?
 

     Thread Starter
 

11/28/2017 5:30 PM  #5


Re: E-brake cable install with MS Cobra rear brakes?

On the aftermarket cables, you just slip the ferrule off of one end of the housing, trim the housing, and then slide it back together.  The housing in under compression when installed so it cannot slip out.  One smart FYI-er used shrink sleeves over the housing and ends to finish it out.
With OEM cables, it is a little more difficult to remove/replace the ferrules, but it can be done.  This is a horse and buggy cable system, not rocket science.  Although, I guess there are some that can imagine it being rocket science and attempt to make it more complicated than it is.


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 

11/29/2017 8:39 AM  #6


Re: E-brake cable install with MS Cobra rear brakes?

MS wrote:

I have some info on this.

Cut the new cable housings to fit between the calipers and the brackets in the drive tunnel, routing above the mufflers and using the original clamps to hold them up under the rear seat area.

Overlap the new cable wire with the original front cable about 6” and apply two 1/8” cable clamps. Tractor Supply has stainless clamps for about $1.99.

If you have a 65, it is better to replace the two front cables and their front spreader bar with the 66 front horseshoe and a single long cable.

If you don’t like the overlap/clamp system, you can build a single wire cable that goes from one caliper to the front, through the hoseshoe and back to the other caliper.

Adjust tension so it is “just tight” when the underdash handle is at rest and the caliper levers are at rest. The brakes will be applied as soon as the caliper levers start to move, so be sure they are at rest with the ebrake not applied.

I did like Steve mentioned and with his cable.  It was on my '65 Fastback and all worked like a dream.  LOL
 


"when I drop something, it always goes to center of the car"
 

12/01/2017 8:31 PM  #7


Re: E-brake cable install with MS Cobra rear brakes?

Thx to all for the thoughts. 
​I need more Wheaties to pull off the ends from my OEM cable, cause they're swaged on there 'Ford Tough'.
Just trying to glean wisdom from others who have boldly gone where no man has gone before and created a better mousetrap.
How's that for mixed metaphors.
I'll add some pics later as the finished product materializes.
 

     Thread Starter
 

12/01/2017 9:06 PM  #8


Re: E-brake cable install with MS Cobra rear brakes?

On the same subject but different... I'm in the process of installing 2017 GT rear calipers and rotors on my 66 coupe using the newly developed MS brackets and Cobra E cables. I purchased the Cobra cables from  Mustang Steve because the 2017 cables as far as I know are only available from Ford and are , for me , cost prohibitive. The only problem I ran in to , but have resolved, is the end of the cable where it attaches to the caliper. On the 2017 caliper the cable fitting is an elongated eye that fits over the e brake lever on the caliper. I resolved the problem by fabbing a fitting that attaches to the existing cable end and fits over the caliper lever.


"anyone that stops learning is old, whether at twenty or eighty"Henry Ford
 

12/02/2017 4:43 PM  #9


Re: E-brake cable install with MS Cobra rear brakes?

MS wrote:

On the aftermarket cables, you just slip the ferrule off of one end of the housing, trim the housing, and then slide it back together.  The housing in under compression when installed so it cannot slip out.  One smart FYI-er used shrink sleeves over the housing and ends to finish it out.
With OEM cables, it is a little more difficult to remove/replace the ferrules, but it can be done.  This is a horse and buggy cable system, not rocket science.  Although, I guess there are some that can imagine it being rocket science and attempt to make it more complicated than it is.

​Gee.  Way back when that's what I did on my 40 Ford.


Original owner - 351w,T-5, 4whl disks, power R&P
 

1/04/2019 7:44 PM  #10


Re: E-brake cable install with MS Cobra rear brakes?

Does anyone have any pictures of the disc brake emergency brake cables routing from the mounting brackets aft?
Thanks

Last edited by Heem (1/04/2019 7:46 PM)


Speed is only a matter of money.  How fast do you want to go?
 

1/05/2019 9:57 AM  #11


Re: E-brake cable install with MS Cobra rear brakes?

I don't have pics but I simply used the original mounting points so my cables use the stock routing.


"anyone that stops learning is old, whether at twenty or eighty"Henry Ford
 

1/05/2019 10:09 AM  #12


Re: E-brake cable install with MS Cobra rear brakes?

Do a search for emergency brake in the tech section.... Info is there along with pics

 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.