FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  » edelbrock carb and aod trans

    • 1 of 1

       

    4/01/2019 4:29 AM  #1

    mark1965
    FYI Addict

    Offline

    Registered: 4/03/2013
    Posts: 172

    edelbrock carb and aod trans

    whos running a edelbrock carb 1403 with an aod convertion. my question is my throttle linkage is the stock steel rod  it i install the sonnex cable corrector kit it show hooking up a throttle cable on a stud no hole for my steel; rod to go in.has anyone ran into this and how did solve  it?

     

    4/02/2019 7:32 AM  #2

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,299

    Re: edelbrock carb and aod trans

    Can you post a pic of your carb clearly showing the section where the linkage hooks up?  And of the new aod linkage?  Going with a custom setup requires some creativity in making up the connections.

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    4/02/2019 9:34 AM  #3

    retired 65
    I FYI 24-7

    Offline

    From: nixa, mo.
    Registered: 4/02/2013
    Posts: 336

    Re: edelbrock carb and aod trans

    I have a 351 motor and edelbrock carb on a street rod, and used the Lokar linkage set-up. I used the adjustment instructions from the Ford shop manual on set-up of the pressures.  I used a pressure gauge on the trans per the shop manual and everything worked great after setting the pressures. LOL  Jerry

    "when I drop something, it always goes to center of the car"
     

    4/06/2019 10:55 AM  #4

    terry
    Senior 24-7 FYI Addict

    Offline

    From: vandalia, illinois
    Registered: 4/01/2013
    Posts: 1,875

    Re: edelbrock carb and aod trans

    Mark did you get your answer?  I have a couple pix of my setup but tinypix wont load.  Send me you email address and I will get the pics to you

     

    4/29/2019 5:52 PM  #5

    mark1965
    FYI Addict

    Offline

    Registered: 4/03/2013
    Posts: 172

    Re: edelbrock carb and aod trans

    terry can you send me those carb linkage setup thanks
     

       •Thread Starter
     

    4/29/2019 7:54 PM  #6

    terry
    Senior 24-7 FYI Addict

    Offline

    From: vandalia, illinois
    Registered: 4/01/2013
    Posts: 1,875

    Re: edelbrock carb and aod trans

    https://photos.app.goo.gl/8Lpm3h1a88sySHZ46

     https://photos.app.goo.gl/ayWfyyBvXhzfxpnZ8

     

     

    1 of 1

  • Index
  •  » FYI Ford, Classic Mustang Tech Discussion
  •  »  edelbrock carb and aod trans

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.