FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

5/07/2019 7:29 AM  #1


water valve motor

I have a 1968 mustang with a 289 engine, I was wondering, does it matter which way  I should hook up the water valve motor.  Does the lower port go to the fire wall or the top port go to the fire wall. Thanks Al. There is no arrow on the valve, the only thing is that theres a upper port and a lower port for the heater hoses.

Last edited by carinfo (5/08/2019 4:44 AM)

 

5/07/2019 12:58 PM  #2


Re: water valve motor

I'm not to sure what a water valve motor is but the lower hose port on the firewall goes to the intake manifold, the upper port goes to the water pump.


Gary Zilik - Pine Junction, Colorado - 67 Coupe, 289-4V, T5
 

5/07/2019 9:34 PM  #3


Re: water valve motor

Is there an arrow for direction of flow?? Valve should be on supply aide of the heater core.


John  -- 67 Mustang Coupe 390 5 speed
 

5/25/2019 8:45 PM  #4


Re: water valve motor

Pressurized water from the intake always goes to the bottom of the heater core. This is to avoid trapping air in the core. The water pump provides suction to pull water from the core’s top fitting.


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 

5/26/2019 6:03 PM  #5


Re: water valve motor

MS wrote:

Pressurized water from the intake always goes to the bottom of the heater core. This is to avoid trapping air in the core. The water pump provides suction to pull water from the core’s top fitting.

It's entirely possible that I am full of the old stuff but I think the Vintage Air Gen IV system has the bottom of the core connected to the upper nipple coming through the firewall.  I seem to recall checking that back in '15 when I put things back together...at least, that's how I have the hoses on the Heap connected......manifold to the upper nipple and pump to the lower.

If someone proves this wrong let me know and I'll change things some day.

BB
 


"you get what you pay for, good work isn't cheap, and there are NO free lunches...PERIOD!"
 

5/26/2019 7:47 PM  #6


Re: water valve motor

Bullet Bob wrote:

MS wrote:

Pressurized water from the intake always goes to the bottom of the heater core. This is to avoid trapping air in the core. The water pump provides suction to pull water from the core’s top fitting.

It's entirely possible that I am full of the old stuff but I think the Vintage Air Gen IV system has the bottom of the core connected to the upper nipple coming through the firewall.  I seem to recall checking that back in '15 when I put things back together...at least, that's how I have the hoses on the Heap connected......manifold to the upper nipple and pump to the lower.

If someone proves this wrong let me know and I'll change things some day.

BB
 

 
Bob, according to the Vintage Air installation manual, the water supply is on top and the return is on bottom. However, I think the Original Poster was asking about the stock heater hose locations for a 68, which Gary answered.

 

5/26/2019 8:59 PM  #7


Re: water valve motor

Exactly, Ron.  Thanks for the ref. to the VA instructions...mine are "stored" in a very safe place, I'm sure.  I was sure the question was referencing a stock setup and I should have been more specific.

BB


"you get what you pay for, good work isn't cheap, and there are NO free lunches...PERIOD!"
 

5/27/2019 6:38 AM  #8


Re: water valve motor

The Vintage Air Gen IV instructions I have indicates the heater control valve goes to the intake manifold (inlet water to the heater core), and the lower hose (outlet) goes to the pump.


65 Fastback, 351W, 5-speed, 4 wheel discs, 9" rear,  R&C Front End.
 

5/27/2019 9:26 AM  #9


Re: water valve motor

BobE wrote:

The Vintage Air Gen IV instructions I have indicates the heater control valve goes to the intake manifold (inlet water to the heater core), and the lower hose (outlet) goes to the pump.

 
That is interesting. I looked at the Vintage Air Gen IV on line installation manual for the current systems they are selling that show the feed from the pump going to the top. How old is your system? Why would they change that?

 

5/27/2019 1:37 PM  #10


Re: water valve motor

Hornman wrote:

BobE wrote:

The Vintage Air Gen IV instructions I have indicates the heater control valve goes to the intake manifold (inlet water to the heater core), and the lower hose (outlet) goes to the pump.

 
That is interesting. I looked at the Vintage Air Gen IV on line installation manual for the current systems they are selling that show the feed from the pump going to the top. How old is your system? Why would they change that?

page 11, figure 6 shows what you've stated Ron.  These could be revised instructions......

 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.