FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

6/30/2019 11:32 AM  #1


Got my rear end exposed!

WHAT??  I took my transmission out and have the rear main exposed, have the new seal.  Question, I know you have to lube the inner part of the seal before installing it. BUT, do I used anything on the outside of the seal?  Like rtv or just oil it or just shove it in there DRY???

Last edited by terry (6/30/2019 11:33 AM)

 

6/30/2019 1:13 PM  #2


Re: Got my rear end exposed!

I would see what the manufacturer recommends.  FelPro, etc. usually have instructions on their website if the seal didn't come with any.  I would really look the crank over too, see if it has a wear groove in it and requires a sleeve.  One piece RMS rarely leak unless the engine has a lot of miles on it. 

If you do use RTV I'd give it a full 24 hours to cure before filling he crankcase.  I've had consistently better lasting sealing from RTV doing that. 

 

6/30/2019 5:04 PM  #3


Re: Got my rear end exposed!

Did that job on my 90 Fox convertible many years ago.  Turned out to be a massive valve cover leak.
I stuck some grease on the OD of the seal as well as oiled the seal surface.  Don't know if right or wrong, but it never leaked.  The important thing is using a driver that fits the seal 100% so you don't bend the seal.  Check out all your old schedule 40 pipe unions.  I think a big'un fits it pretty good.


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 

6/30/2019 6:19 PM  #4


Re: Got my rear end exposed!

I used a oil filter tool cup and pounded it in my sons 5.8.  I put RTV around the outside of the seal after is was in so it was flush and smooth. After I installed the pan I did the same thing.

 

6/30/2019 7:07 PM  #5


Re: Got my rear end exposed!

Never done it unless engine was dis-assembled and on stand.
Don't chew hafta remove the rear main bearing saddle or sump'thin?
6sal6


Get busy Liv'in or get busy Die'n....Host of the 2020 Bash at the Beach/The only Bash that got cancelled  )8
 

6/30/2019 9:02 PM  #6


Re: Got my rear end exposed!

Nope, not for a 1 piece. 

 

7/01/2019 9:01 AM  #7


Re: Got my rear end exposed!

Terry there is that You Tube video on remove/replace one piece 302 main seal, find the one that shows how to convert a PVC pipe cap into a seal driver.
Might find some who'd disagree, however I'd apply a very thin coat of Permatex to the seal before seatiing.
Glad Ya got the tranny out.

Tubo


If it ain't broke, I haven't modified it Yet
 

7/02/2019 5:35 AM  #8


Re: Got my rear end exposed!

I got the seal installed and decided to re do the oil pan gasket while it was all exposed.  Have to pick up new gasket and RTV today and hope to start reassembly tonight.

When I put the flywheel bolts back on should I use something on the threads?  It appears there was something on them when I took them off but cant tell what it is.

     Thread Starter
 

7/02/2019 5:51 AM  #9


Re: Got my rear end exposed!

Pretty sure crank is drilled and threaded right threw, so you have to seal bolts or or have another slight oil leak.

 

7/02/2019 3:49 PM  #10


Re: Got my rear end exposed!

What Jim said .... plus sealer on the two rear large pan bolts.


"Those telephone poles were like a picket fence"
 

7/02/2019 7:57 PM  #11


Re: Got my rear end exposed!

Not RTV


70, ragtop 351W/416 stroker Edel Performer heads w pro flow 4, Comp roller 35-421-8. T5
 

7/02/2019 8:10 PM  #12


Re: Got my rear end exposed!

Terry I used Permatex High Temperature Thread Sealant (Item #59214) on my threads.  Looks like hi temp pipe dope to me in a small tube.  Hope this is helpful.

 

7/03/2019 9:48 AM  #13


Re: Got my rear end exposed!

Right. The flywheel bolts need sealant. Apply to the BOLT THREADS, not the female threads in the hole, so you don’t push goop into the inside of the engine. 351w has blind holes, so not needed on those. 289, 302, 5.0 have holes open to the crankcase.

In reality, darn near any type sealer or rtv will work for this. Just get all the old oil off both threads first.


Money you enjoy wasting is NOT wasted money... unless your wife finds out.
 

Board footera


REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.