FYI FORD - MustangSteve's Ford Mustang Forum
The Internet's Most Knowledgeable Classic Mustang Information
IF YOU HAVE A QUESTION ABOUT CLASSIC FORD MUSTANGS, YOU HAVE COME TO THE RIGHT PLACE!
MustangSteve has over 30 years of Mustang experience, having owned 30 of them and restored several others. With the help of other Mustangers, this site is dedicated to helping anyone wanting to restore or modify their Mustang.... THERE ARE NO DUMB QUESTIONS!!!!!
Visit MustangSteve's web site to view some of my work and find details for:
FYIFORD Contributors' PICTURES - Power Brake Retrofit Kits for 65-66 Stangs - Classic Mustang FAQ's by MustangSteve - How to wire in a Duraspark Ignition - Mustang Ride Height Pictures and Descriptions - Steel Bushings to fit Granada Spindles to Mustang Tie Rods - Visit my EBAY store MustangSteve Performance - How to Install Granada Disc Brakes MustangSteve's Disc Brake Swap Page - FYIFORD Acronyms for guide to all the acronyms used on this page - FYIFORD Important information and upcoming events

You are not logged in. Would you like to login or register?

  • Index
  •  » Swap Meet
  •  » 57/59 nine housing with axles

    • 1 of 1

       

    12/30/2020 10:26 AM  #1

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,675

    57/59 nine housing with axles

    I was going to narrow this housing but figured I would try to sell it and buy a new housing that will be 6 inches narrower. I should have the housing blasted and sealed in epoxy this weekend. The housing currently has the leaf spring pads tacked in place for my setup. I can weld the pads in the correct 43 center line. It will need new axle bearings.


    double dog dare rescue

     

    1/05/2021 8:41 PM  #2

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,675

    Re: 57/59 nine housing with axles

    It’s a small bearing axle. It’s been sand blasted and sealed in epoxy primer but the leaf spring pads have not been fully welded yet in case they need to be placed in a different location.

       •Thread Starter
     

    1/13/2021 12:32 PM  #3

    MS
    Forum Originator

    Offline

    From: Canyon Lake, Texas
    Registered: 1/24/2013
    Posts: 12,186

    Re: 57/59 nine housing with axles

    Wish you were closer. I would own that thing!

    Money you enjoy wasting is NOT wasted money... unless your wife finds out.
     

    1/13/2021 2:41 PM  #4

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,675

    Re: 57/59 nine housing with axles

    MS wrote:

    Wish you were closer. I would own that thing!

     I can ship it.  I've shipped bare housings before through UPS.  Just tape a label to the axle tube and off it goes.  

       •Thread Starter
     

    1/13/2021 2:48 PM  #5

    RTM
    Senior 24-7 FYI Addict

    Offline

    From: Cape Coral FL
    Registered: 5/22/2019
    Posts: 1,675

    Re: 57/59 nine housing with axles

    In epoxy primer.


    what is my tumblr url

       •Thread Starter
     

     

    1 of 1

  • Index
  •  » Swap Meet
  •  »  57/59 nine housing with axles

    • Board footera


    REMEMBER!!! When posting a question about your Mustang or other Ford on this forum, BE SURE to tell us what it is, what year, engine, etc so we have enough information to go on.